CONTINUOUSWAVE

conch

Might be easier to identify if you remove it from the door and post a picture. A locksmith can probably identify the marks or recommend a replacement for you.
Chuck

conch

For many Yamaha key switches remove the retaining nut and located on the flat side of the switch key barrel should be a three digit key number. With the key number you can source a replacement.
Chuck

conch

Moabelite can you please post pictures of your 1996 OUTRAGE 24 when you bring her home. I would like to see your 1996 OUTRAGE 24 in the water with fuel tanks at FULL level. You sound like you will enjoy this hull.

Are the Yamaha engines V6 two-stroke-power-cycle engines?

Chuck

conch

Nice boat, pretty heavy girl though. Will you keep her forever and ever, or do you consider resale? A 30K premium for 60% more horsepower is about 10% or less of the purchase price. Not out of range for boats or pickup trucks I think. Put the 400 Merc's on there or you will piloting a 13,000 lb pig ...

conch

The Yamaha SWS II 17-pitch propeller diameter is 15.5-inches, and the suffix is T, not M. I am not clear what propeller you have. The boat seems to be running well now. Try a magical four-blade--but I doubt performance will improve much or the engine will be able to accelerate to 6100-RPM. A Yamaha ...

conch

I like it for the stainless steel bolts used to mount aluminum outrigger bases,and lower unit bolts. The ss bolts on the aluminum trailer also. Lots of places on a boat, motor, and trailer used in salt water.
Chuck

conch

Here are a pair of Ox 66 Yamaha engine with rigging located in Delaware. Listed on the boating site THT. Selling pair of YAMAHA V225 Saltwater Series 11 0X66 fuel injected they are scheduled to be removed from boat Dec 16, These motors have 500hrs on them and are running, all harnesses,switches,gaug...

conch

The Yamaha site indicates the 425 XTO is also available in 35 in.
Chuck

conch

Yamaha is offering the F300 with a 35-inch shaft length in their F300 with electronic shifting. The others will probably be close behind.

Yamaha literature wrote:Shaft lengths available: 25”, 30” and 35” (35” on F300 DEC only)

Chuck

conch

A1. I am using two Garmin 740s MFD presently. Have used 4xx,5xx,740, and the 4xxx,5xxx,6xxx, with the 19x GPS also. A2. I have been very pleased with Garmin products,ease of installation,updating, and networking, and support. A3. I would pick Garmin again. I put the biggest Garmin I can fit for thes...

conch

Always liked this model, good luck with your sale.
Chuck

conch

Do you have a picture of the routered joint for the two panels and where you decided to place the seam?
Looks good,
Chuck

conch

For-sale: 1986 Montauk 17 with 2003 Yamaha 90 and 2011 Karavan Trailer all in good condition for $8,750. Located in Islamorada, Fl 33036 E-mail clv149pdo@aol.com

conch

This 1985 18' Outrage @ 8K deserves a look. I will try to put a link, but I saw it at the site ' THT " in the classified section.
https://www.thehulltruth.com/boats-sale ... wn-sc.html

Chuck

conch

Seal 3/4in. is in the mail from Islamorada.
Chuck

conch

My 1996 Seastar Pro tilt helm is model HH5774 2.0 cu.in. You did not say where yours is leaking. Rebuild kits for the helm [being sold on] Amazon are around $40. If just the shaft seal is leaking I have both dash-210 & dash-214 (3/4 & 1in quad rings) I can mail to you. Let me know. I also ha...

conch

Thank you very much for the offer Rich and I will let you know. I do have hub kits for the Yamaha, both Flo-Torq II and Solas/Rubex #203. Was your T-top cloth material or fiberglass? I have never watched the cutting and installation of mounts (antenna,radar,lights,etc.) thru the cloth. Some articles...

conch

Looks good, you could mount your VHF out of sight and use a remote microphone taking up very little space on your dash.
Chuck

conch

Hi Archie. [Total crew weight associated with the anecdotal performance data reported above was] probably about 850-lbs. There were two were small children and five adults aboard. There was no gear on board other than safety gear. We just grabbed the LASER 19-pitch propeller on the way to launch whe...

conch

When you get your Whaler, a location to start measuring for separating the lifting bunks would be the width from outside of the transom splashwell drain holes and across to the inside of the lifting eyes on each side. That should get it. Look at some pictures of the 15' classic transom in the refere...

conch

On my 21 JUSTICE with Yamaha F300 I am going to try a Yamaha SWS II 19-pitch propeller soon. I have a borrowed Mercury Laser 19 now just to bring the boat home, and performance was poor all around. I did not try much of anything, just running home from the ramp. Seven on board and 50 gallons fuel. B...

conch

Thru-hull fittings look good so far, though they will be replaced with stainless probably next time on the trailer. The cockpit floor boxes both have 1-1/4-inch bronze thru-hull fittings which are capped. Not sure what I will do with them, maybe a washdown or livewell pump. Stern splash well drains ...

conch

Thanks Jim, the lower unit serial number is unique unto itself, however in the Yamaha computer system entering the engine (powerhead number) or this new lower unit number ,reveals the other one and shows my name and address as owner and my Extended Warranty info.
Chuck

conch

Hi, battery isolator is what Yamaha calls their aux battery lead. I believe the the fuse included in the kit protects the wiring and the service manual states the aux lead output at a max of 70 amps @ 12v. The reset able fuse is located near to the aux battery, and the other lead from the engine is ...

conch

: Fig. 1. Yamaha puts a serial number on lower unit of F300 NCA model; Yamaha Lower Serial #.JPG (42.05 KiB) Viewed 8067 times

: Fig. 2. Boat on lift.; 21 on Lift.jpg (56.28 KiB) Viewed 8067 times

I am trying a vented engine cover that stays on all the time .

: Fig. 3. Dive Door removed for Hurricane Prep; 21 Bston Whaler 3.jpg (69.73 KiB) Viewed 7916 times

conch

The rigging of the new Yamaha [F300] engine has begun [on the 1995 JUSTICE 21 re-power]. As part of pre-rigging cleaning I had the fuel tank examined, pressure tested, drained, and cleaned, The fuel line hoses and tank level float gauge were replaced. The O-ring on the filler cap was . This service ...

conch

Over 3,000 miles round trip.
Chuck

conch

I have completed a few installations of rigging before the storm and will post some in the repairs and performance sections.
I think we have agreed to name her "REEL JUSTICE"
Chuck

conch

The dive door just fits that well into the opening to look sealed and it still has all its original sealing rubber and clamps. I doubt it was ever used much. The original custom short bungee cords to hold/store the door when removed into two chocks on deck were still sealed in a bag in the owners po...

conch

CW member MAVERICK had a beautiful restored 1987 18' GUARDIAN with DIVE DOOR that he sold here in the Marketplace around Oct of 2017. Search the listing for pics. I just was not ready yet. In hindsight after looking and operating both, I prefer the 21' Justice with a four stroke Yamaha F300 vs the E...

conch

The grand children asked me to rig one more Boston Whaler. With some different medicines I am feeling better now, so I am going to try. At first I was set on searching for a classic 18, but after seeing some of the fuel tank/deck problems others have had I started to look for something different. Th...

conch

Due to a re-power I have for sale Mercury rigging and parts from an excellent condition Mercury OptiMax 225 XL: a midsection, a harnesses, an oil tank, and a top mount binnacle. These are from a freshwater lake motor from Oklahoma. The power trim and tilt appears as new and will fit many engines. No...

conch

Butch, a bilge pump connected directly to the battery has another switch of some type somewhere to act upon the presence of water or it would run all the time. I like a separate switch for the NMEA-2000 system to be able to reboot or work on the system. This way the MFD,s or other items on the backb...

conch

Among myself and my two next door neighbors we have 9 F300 Yamaha's all 2015 4.2 L models put in service in 2016. We all have the optional water pressure sensors and battery isolator leads installed since new. All motors run in very warm salt water. I rinse my motors religiously after each use, my n...

conch

I try to avoid drilling holes in the hull. Search on this site and you will learn how to fill and seal the old screw holes. I use the products from Stern Saver to fasten things to the hull in addition to transducers. My bilge pump and Racor filters are screwed into the Stern Saver blocks. The blocks...

conch

FOR HAWAIIAN WHALER Q: Can you share the info you received from Boston Whaler regarding the transom scuppers? The transom scuppers were probably used on many models for many years. I missed Mr. Bennett by a few days after his retirement. The person who answered was friendly but could not provide any...

conch

Sounds good, maybe you could add your location and a picture. I think this will be gone soon. Any idea about the fuel tank condition.
Good luck with your sale.
Chuck

conch

dtmackey -- the OP never mentioned "homemade" in his post. He did ask for opinions on a few of his ideas which he listed. I gave him my opinion on the one idea of his involving obvious fraud. No "rush to judgement", and the law seems clear to me. Many stolen trailers come back to...

conch

Go to your local county tax collectors office in Florida. Take your Grandmother with you and fill out Form HSMV 82152 and you can get same day title service. She should bring the death certificate and her marriage license. If she is not available fill out form HSMV 82040 and bring along death certif...

conch

...I sold a boat and trailer years ago and forgot to give the buyer the title. I still have it. I would use this title to get a registration and plates . I should probably say that I'm a retired cop, and I never stopped a trailer in my entire career. But even if I did, I can't imagine I would have ...

conch

If you will be using your auxiliary engine regularly, mount a permanent bracket--either fixed or adjustable and available from several vendors/ Or make your own. Most brackets I have seen are mounted to the transom. The on-off and fastening and clamping is done to a block of replaceable wood or simi...

conch

PRICE REDUCED

conch

Looks very nice, though I have never seen a V4 Johnson bolted on to a transom quite like that.
Chuck

conch

Will be back to Natchez, Ms as soon as the Doc's say I can travel that far again.
Chuck

conch

More inside pics

conch

Interior pics

conch

Lobster Magnet First day of Mini Season

conch

Be first to the launch ramp with this classic For sale is my 1996 Corvette Convertible LT4 6 speed White with tan leather, tan soft top White Factory hardtop with rolling storage cart Car covers full and top down Original sawblades New battery Run flat tires All factory paperwork, build sheet, opera...

conch

Link to Suzuki pictures I cannot seem to resize them to fit.
https://www.thehulltruth.com/trucks-tra ... i-4x4.html
Chuck

conch

Thanks for help with the pictures Phil
This link should have pictures of the Suzuki 4X4
Purchase the combo for 9K and be ready for any adventure.
https://www.thehulltruth.com/trucks-tra ... i-4x4.html

Search found 152 matches