Search found 172 matches

by conch
Mon Aug 28, 2023 2:41 pm
Forum: VHF MARINE RADIO
Topic: VHF Marine Band DSC Radios 2023
Replies: 5
Views: 1060

Re: VHF Marine Band DSC Radios 2023

Yes, the SH website seems dated by a few years. I also have a GX2200 and think the GX2400 only added NMEA 2000 connection ability.
by conch
Mon Aug 28, 2023 1:26 pm
Forum: VHF MARINE RADIO
Topic: VHF Marine Band DSC Radios 2023
Replies: 5
Views: 1060

Re: VHF Marine Band DSC Radios 2023

I have a model GX2400 from Standard Horizon and it does have an internal GPS receiver.
by conch
Tue Sep 20, 2022 11:59 am
Forum: The GAM
Topic: Polymer Sealer Advertised on Television
Replies: 2
Views: 1440

Re: Polymer Sealer Advertised on Television

I have seen POLIGLOW Poli-Strip used to remove a finish on gel coat.. The same results nay be obtained from ZEP Heavy Duty Floor Wax Remover. Sanding will get off the polymer sealer advertised on television. In the end sanding may be necessary to remove polymer sealer advertised on television. LINKS...
by conch
Wed May 11, 2022 8:18 pm
Forum: PERFORMANCE
Topic: Affect on Performance of Reducing Power and Power Stroke Design
Replies: 5
Views: 3380

Affect on Performance of Reducing Power and Power Stroke Design

Moving down approximately 40% in horsepower [and] switching to four-stroke-power-cycle engine from a two-stroke-stroke-power-cycle engine may not result in the same performance.
by conch
Sun May 08, 2022 10:56 am
Forum: The GAM
Topic: 1987 Whaler 27 Three Fuel Tanks
Replies: 9
Views: 2348

Re: 1987 Whaler 27 Three Fuel Tanks

Try listening at the tank vent on the hull side as you add some fuel or some air from a compressor to isolate the fill opening.
by conch
Tue Apr 26, 2022 12:21 pm
Forum: The GAM
Topic: Identify Boat From HIN and Picture
Replies: 6
Views: 2391

Re: Identify Boat From HIN and Picture

A hull from Commercial Products Division (CPD) of Boston Whaler is not automatically a red dot. The extra lay up of resin and cloth was a stand alone option that could be ordered or not. The Red Dot or Black Dot placed in the gelcoat acknowledged that installed option.
by conch
Sun Apr 24, 2022 3:38 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1992 Challenger 25 Dive Door Structure
Replies: 2
Views: 721

Re: 1992 Challenger 25 Dive Door Structure

Show pictures of the area [of the CHALLENGER 25 dive door that has damage]. They might save you from a thousand wrong answers. Three door sizes were offered. Q2: what is the width of the dive door under discussion? Q3: is there a stainless steel guard around the door opening? Q4: do you have the doo...
by conch
Fri Mar 18, 2022 9:07 am
Forum: The GAM
Topic: 1978 15-footer Red Dot Restoration
Replies: 5
Views: 1151

Re: 1978 15-footer Red Dot Restoration

Can you post up a picture of the red dots on the sides of your hull for us all to see?
Thanks
by conch
Wed Mar 02, 2022 3:06 pm
Forum: SMALL BOAT ELECTRICAL
Topic: Tachometer for Yamaha F70 Engine; Trolling Switch
Replies: 5
Views: 3985

Re: Tachometer for Yamaha F70 Engine; Trolling Switch

Joe--the F70 can be [networked] to a MFD using a Lowrance cable # 120-37 using NMEA 2000 to be able to see the engine speed and much more engine data. The necessary network special drop cable is available most everywhere including Amazon: https://www.amazon.com/Lowrance-000-0120-37-Yamaha-Engine-Int...
by conch
Sun Dec 05, 2021 11:52 am
Forum: PERFORMANCE
Topic: 23 CONQUEST Twin Yamaha F150 Engines
Replies: 36
Views: 28199

Re: 23 CONQUEST Twin Yamaha F150 Engines

For a boat with gear and people normally carried, a good indication that the propeller and engine are dialed-in is for the engine to accelerate to [close to the particular engine's maximum allowed engine speed] at full throttle.
by conch
Sun Dec 05, 2021 8:44 am
Forum: PERFORMANCE
Topic: 23 CONQUEST Twin Yamaha F150 Engines
Replies: 36
Views: 28199

Re: 23 CONQUEST Twin Yamaha F150 Engines

[The boat speed obtained in the test using the three-bladed 17-pitch aluminum Yamaha propellers] looks really good.

[A top boat speed of] maybe 51 to 53-MPH [might be obtained] once [the engine and propellers are] dialed-in and some fuel is added.
by conch
Fri Oct 15, 2021 2:58 pm
Forum: PERFORMANCE
Topic: 23 CONQUEST Twin Yamaha F150 Engines
Replies: 36
Views: 28199

Re: 23 CONQUEST Twin Yamaha F150 Engines

I think the engines will surely need to be raised. ASIDE ON SEVERAL OTHER NON-PERFORMANCE RELATED TOPICS DEC electrical controls with the 6Y9 gauge is the best combination and takes the least dash space. The 6Y9 came in several versions, I assume yours is new and not used. Carefully check the fuel s...
by conch
Fri Oct 15, 2021 10:52 am
Forum: PERFORMANCE
Topic: 23 CONQUEST Twin Yamaha F150 Engines
Replies: 36
Views: 28199

Re: 23 CONQUEST Twin Yamaha F150 Engines

Did you keep the REVOLUTION4 propellers you previously purchased? What size were those REVOLUTION4 propellers? The new engine with a gear ratio of 2:1 will spin the REVOLUTION4 just fine. [The engine mounting should be] at least two-holes-up to begin [testing propellers]. Do your old four-bladed pro...
by conch
Thu Oct 14, 2021 1:27 pm
Forum: PERFORMANCE
Topic: 23 CONQUEST Twin Yamaha F150 Engines
Replies: 36
Views: 28199

Re: 23 Conquest repowered with twin Yamaha F150s

You have made a nice re-power. I suggest using Mercury REVOLUTION4 17-pitch. They should give stern lift. I like the Rubex hubs to quiet the shifting sounds. Visit Propgods.com for excellent propeller information and a website to ask questions. Propgods ships propellers for testing through the mail ...
by conch
Wed May 05, 2021 8:34 pm
Forum: MARKETPLACE
Topic: FS 1984 Montauk w 2009 90hp Yamaha &Trailer Florida
Replies: 2
Views: 4405

Re: FS 1984 Montauk w 2009 90hp Yamaha &Trailer Florida

SOLD SOLD SOLD
Seller wrote me a thank you for passing his info.
Think it was someone from here Who are you lucky buyer? Some kind of sale record I think.
Chuck
by conch
Wed May 05, 2021 5:44 pm
Forum: MARKETPLACE
Topic: FS 1984 Montauk w 2009 90hp Yamaha &Trailer Florida
Replies: 2
Views: 4405

FS 1984 Montauk w 2009 90hp Yamaha &Trailer Florida

I do not remember if we can give a purchase lead to fellow CW members anymore. Here is a Montauk with a 168 hour 90Hp Yamaha with a 10/2008 build date. Hull looks about right for an 1984 though the trailer is rough. $7,800 asking Cape Coral, Florida I do not think you would get hurt with this one, m...
by conch
Sun May 02, 2021 9:40 am
Forum: PERFORMANCE
Topic: 1998 Outrage 20 Engine Mounting Height
Replies: 7
Views: 8290

Re: 1998 Outrage 20 Engine Mounting Height

Let the dealer have his way with you. Q1: New engine, right? You will try several propellers and heights until you have propeller and engine mounting height dialed in. Q2: Does your purchase agreement give you the option of getting the setup correct? If [the engine mounting height is judged to be to...
by conch
Sun Apr 25, 2021 9:43 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1996 MONTAUK 17: Leak at cockpit sump drain
Replies: 54
Views: 22832

Re: 1996 MONTAUK 17: Leak at cockpit sump drain

Most likely [the leak is a result of] sealant failure. If Twin Cities marine is sending a replacement part that is the same part as was originally installed, I would use that part. Brass [drain] tubes went out of fashion [at Boston Whaler], and Peter Van Lancker made many changes [to Boston Whaler b...
by conch
Sun Apr 18, 2021 9:27 am
Forum: The GAM
Topic: The WHALER 27 Models and hull dimensions
Replies: 2
Views: 3147

Re: The WHALER 27 Models and hull dimensions

Was the 27 Center Console Cuddy Cabin called an Outrage in the sales literature? Or, was it just known as the CCC model? Lightest of all the 27s. Also the 27s appear to be the only models that do not increase rated horsepower capacity with the addition of Whaler Drive. Whaler Drive, brackets, or a c...
by conch
Thu Apr 15, 2021 8:36 am
Forum: MARKETPLACE
Topic: SOLD: Tandem-axle Trailer in Florida $495 SOLD
Replies: 0
Views: 6615

SOLD: Tandem-axle Trailer in Florida $495 SOLD

For sale: a 1996 Dorsey welded tandem-axle boat trailer rated for 6,000-GVWR with 2-inch-ball hitch in Islamorada, Florida for $495. CONTACT: clv149pdo@aol.com This trailer was used in fresh water until the 2020 summer. It had four new tires plus spare at that time. I towed my 21 JUSTICE from Oklaho...
by conch
Sat Jun 13, 2020 10:31 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1986 Frontier 25 Sliding Door Latch Manufacturer
Replies: 3
Views: 1889

Re: 1986 Frontier 25 Sliding Door Latch Manufacturer

Might be easier to identify if you remove it from the door and post a picture. A locksmith can probably identify the marks or recommend a replacement for you.
Chuck
by conch
Sat Jun 13, 2020 10:09 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1985 Yamaha 40 Replacement Key for Ignition Key Switch
Replies: 8
Views: 2755

Re: 1985 Yamaha 40 Replacement Key for Ignition Key Switch

For many Yamaha key switches remove the retaining nut and located on the flat side of the switch key barrel should be a three digit key number. With the key number you can source a replacement.
Chuck
by conch
Sun Jun 07, 2020 8:47 am
Forum: The GAM
Topic: 1996 OUTRAGE 24 Ride and Stability
Replies: 28
Views: 19333

Re: 1996 OUTRAGE 24 Ride and Stability

Moabelite can you please post pictures of your 1996 OUTRAGE 24 when you bring her home. I would like to see your 1996 OUTRAGE 24 in the water with fuel tanks at FULL level. You sound like you will enjoy this hull.

Are the Yamaha engines V6 two-stroke-power-cycle engines?

Chuck
by conch
Mon May 25, 2020 9:30 am
Forum: The GAM
Topic: 2020 320 VANTAGE Engine Options
Replies: 14
Views: 5083

Re: 2020 320 VANTAGE Engine Options

Nice boat, pretty heavy girl though. Will you keep her forever and ever, or do you consider resale? A 30K premium for 60% more horsepower is about 10% or less of the purchase price. Not out of range for boats or pickup trucks I think. Put the 400 Merc's on there or you will piloting a 13,000 lb pig ...
by conch
Tue Apr 21, 2020 9:56 am
Forum: PERFORMANCE
Topic: 1994 OUTRAGE 24 250-HP
Replies: 11
Views: 5979

Re: 1994 OUTRAGE 24 250-HP

The Yamaha SWS II 17-pitch propeller diameter is 15.5-inches, and the suffix is T, not M. I am not clear what propeller you have. The boat seems to be running well now. Try a magical four-blade--but I doubt performance will improve much or the engine will be able to accelerate to 6100-RPM. A Yamaha ...
by conch
Sun Apr 19, 2020 10:45 am
Forum: REPAIRS and MODIFICATIONS
Topic: TEF-GEL
Replies: 1
Views: 1283

Re: TEF-GEL

I like it for the stainless steel bolts used to mount aluminum outrigger bases,and lower unit bolts. The ss bolts on the aluminum trailer also. Lots of places on a boat, motor, and trailer used in salt water.
Chuck
by conch
Sat Dec 14, 2019 8:40 am
Forum: The GAM
Topic: New purchase: 1991 Walkaround 21
Replies: 16
Views: 6121

Re: New purchase: 1991 Walkaround 21

Here are a pair of Ox 66 Yamaha engine with rigging located in Delaware. Listed on the boating site THT. Selling pair of YAMAHA V225 Saltwater Series 11 0X66 fuel injected they are scheduled to be removed from boat Dec 16, These motors have 500hrs on them and are running, all harnesses,switches,gaug...
by conch
Thu Nov 14, 2019 9:27 am
Forum: PERFORMANCE
Topic: Yamaha F300 35-inch Shaft Length Now Available
Replies: 4
Views: 3190

Re: Yamaha F300 now available as 35in model

The Yamaha site indicates the 425 XTO is also available in 35 in.
Chuck
by conch
Tue Nov 12, 2019 9:22 am
Forum: PERFORMANCE
Topic: Yamaha F300 35-inch Shaft Length Now Available
Replies: 4
Views: 3190

Yamaha F300 35-inch Shaft Length Now Available

Yamaha is offering the F300 with a 35-inch shaft length in their F300 with electronic shifting. The others will probably be close behind.
Yamaha literature wrote:Shaft lengths available: 25”, 30” and 35” (35” on F300 DEC only)

Chuck
by conch
Sun Nov 10, 2019 4:37 pm
Forum: SMALL BOAT ELECTRICAL
Topic: SURVEY of Multi-function Display Choice
Replies: 6
Views: 6520

Re: SURVEY of Multi-function Display Choice

A1. I am using two Garmin 740s MFD presently. Have used 4xx,5xx,740, and the 4xxx,5xxx,6xxx, with the 19x GPS also. A2. I have been very pleased with Garmin products,ease of installation,updating, and networking, and support. A3. I would pick Garmin again. I put the biggest Garmin I can fit for thes...
by conch
Sun Nov 10, 2019 11:23 am
Forum: MARKETPLACE
Topic: SOLD: 1997 Outrage 24 $16,500 Long Island, New York
Replies: 4
Views: 3701

Re: 1997 Outrage 24' $18,500

Always liked this model, good luck with your sale.
Chuck
by conch
Wed Oct 23, 2019 12:44 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1986 OUTRAGE 18 Replace Deck with PVC Sheet; New Fuel Tank
Replies: 40
Views: 54613

Re: 1986 OUTRAGE 18 Replace Deck with PVC Sheet; New Fuel Tank

Do you have a picture of the routered joint for the two panels and where you decided to place the seam?
Looks good,
Chuck
by conch
Sat Sep 28, 2019 11:36 am
Forum: MARKETPLACE
Topic: FS: 1986 Montauk, 90Hp Yamaha, Karavan Trailer
Replies: 1
Views: 8313

FS: 1986 Montauk, 90Hp Yamaha, Karavan Trailer

For-sale: 1986 Montauk 17 with 2003 Yamaha 90 and 2011 Karavan Trailer all in good condition for $8,750. Located in Islamorada, Fl 33036 E-mail clv149pdo@aol.com
by conch
Fri Sep 27, 2019 12:50 pm
Forum: MARKETPLACE
Topic: WTB: 18 to 22 Outrage Atlanta Area or Southeast
Replies: 8
Views: 10981

Re: WTB: 18 to 22 Outrage Atlanta Area or Southeast

This 1985 18' Outrage @ 8K deserves a look. I will try to put a link, but I saw it at the site ' THT " in the classified section.
https://www.thehulltruth.com/boats-sale ... wn-sc.html

Chuck
by conch
Thu Sep 12, 2019 1:26 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1994 Outrage 21 Steering Leak
Replies: 4
Views: 8375

Re: 1994 Outrage 21 Steering Leak

Seal 3/4in. is in the mail from Islamorada.
Chuck
by conch
Wed Sep 11, 2019 12:50 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1994 Outrage 21 Steering Leak
Replies: 4
Views: 8375

Re: 1994 Outrage 21 Steering Leak

My 1996 Seastar Pro tilt helm is model HH5774 2.0 cu.in. You did not say where yours is leaking. Rebuild kits for the helm [being sold on] Amazon are around $40. If just the shaft seal is leaking I have both dash-210 & dash-214 (3/4 & 1in quad rings) I can mail to you. Let me know. I also ha...
by conch
Sun Sep 08, 2019 12:10 pm
Forum: PERFORMANCE
Topic: 1996 21 JUSTICE F300
Replies: 6
Views: 9501

Re: 1996 21 JUSTICE F300

Thank you very much for the offer Rich and I will let you know. I do have hub kits for the Yamaha, both Flo-Torq II and Solas/Rubex #203. Was your T-top cloth material or fiberglass? I have never watched the cutting and installation of mounts (antenna,radar,lights,etc.) thru the cloth. Some articles...
by conch
Sun Sep 08, 2019 8:33 am
Forum: The GAM
Topic: New Boat: 1987 SUPER SPORT LIMITED 17
Replies: 6
Views: 10235

Re: Finally got a whaler, and took it out! Lots of projects

Looks good, you could mount your VHF out of sight and use a remote microphone taking up very little space on your dash.
Chuck
by conch
Sun Sep 08, 2019 8:14 am
Forum: PERFORMANCE
Topic: 1996 21 JUSTICE F300
Replies: 6
Views: 9501

Re: 1996 21 JUSTICE F300

Hi Archie. [Total crew weight associated with the anecdotal performance data reported above was] probably about 850-lbs. There were two were small children and five adults aboard. There was no gear on board other than safety gear. We just grabbed the LASER 19-pitch propeller on the way to launch whe...
by conch
Sat Sep 07, 2019 10:07 am
Forum: The GAM
Topic: SUPER SPORT 15 Boat Lift Set-up
Replies: 3
Views: 7737

Re: SUPER SPORT 15 Boat Lift Set-up

When you get your Whaler, a location to start measuring for separating the lifting bunks would be the width from outside of the transom splashwell drain holes and across to the inside of the lifting eyes on each side. That should get it. Look at some pictures of the 15' classic transom in the refere...
by conch
Sat Sep 07, 2019 9:34 am
Forum: PERFORMANCE
Topic: 1996 21 JUSTICE F300
Replies: 6
Views: 9501

1996 21 JUSTICE F300

On my 21 JUSTICE with Yamaha F300 I am going to try a Yamaha SWS II 19-pitch propeller soon. I have a borrowed Mercury Laser 19 now just to bring the boat home, and performance was poor all around. I did not try much of anything, just running home from the ramp. Seven on board and 50 gallons fuel. B...
by conch
Sat Sep 07, 2019 8:38 am
Forum: The GAM
Topic: 1996 21' Justice Refurbishment
Replies: 8
Views: 9785

Re: 1996 21' Justice Refurbishment

Thru-hull fittings look good so far, though they will be replaced with stainless probably next time on the trailer. The cockpit floor boxes both have 1-1/4-inch bronze thru-hull fittings which are capped. Not sure what I will do with them, maybe a washdown or livewell pump. Stern splash well drains ...
by conch
Fri Sep 06, 2019 1:31 pm
Forum: The GAM
Topic: 1996 21' Justice Refurbishment
Replies: 8
Views: 9785

Re: 1996 21' Justice Refurbishment

Thanks Jim, the lower unit serial number is unique unto itself, however in the Yamaha computer system entering the engine (powerhead number) or this new lower unit number ,reveals the other one and shows my name and address as owner and my Extended Warranty info.
Chuck
by conch
Thu Sep 05, 2019 8:20 pm
Forum: The GAM
Topic: 1996 21' Justice Refurbishment
Replies: 8
Views: 9785

Re: 1996 21' Justice Refurbishment

Hi, battery isolator is what Yamaha calls their aux battery lead. I believe the the fuse included in the kit protects the wiring and the service manual states the aux lead output at a max of 70 amps @ 12v. The reset able fuse is located near to the aux battery, and the other lead from the engine is ...
by conch
Thu Sep 05, 2019 1:08 pm
Forum: The GAM
Topic: 1996 21' Justice Refurbishment
Replies: 8
Views: 9785

Re: 1996 21' Justice Re-Power

Yamaha Lower Serial #.JPG
Fig. 1. Yamaha puts a serial number on lower unit of F300 NCA model
Yamaha Lower Serial #.JPG (42.05 KiB) Viewed 9781 times


21 on Lift.jpg
Fig. 2. Boat on lift.
21 on Lift.jpg (56.28 KiB) Viewed 9781 times


I am trying a vented engine cover that stays on all the time .

21 Bston Whaler 3.jpg
Fig. 3. Dive Door removed for Hurricane Prep
21 Bston Whaler 3.jpg (69.73 KiB) Viewed 9630 times
by conch
Thu Sep 05, 2019 1:04 pm
Forum: The GAM
Topic: 1996 21' Justice Refurbishment
Replies: 8
Views: 9785

1996 21' Justice Refurbishment

The rigging of the new Yamaha [F300] engine has begun [on the 1995 JUSTICE 21 re-power]. As part of pre-rigging cleaning I had the fuel tank examined, pressure tested, drained, and cleaned, The fuel line hoses and tank level float gauge were replaced. The O-ring on the filler cap was . This service ...
by conch
Thu Sep 05, 2019 11:16 am
Forum: The GAM
Topic: Towing Home My "Barn Find"
Replies: 9
Views: 11438

Re: Towing Home My "Barn Find"

Over 3,000 miles round trip.
Chuck
by conch
Wed Sep 04, 2019 8:59 am
Forum: The GAM
Topic: Towing Home My "Barn Find"
Replies: 9
Views: 11438

Re: Towing Home My "Barn Find"

I have completed a few installations of rigging before the storm and will post some in the repairs and performance sections.
I think we have agreed to name her "REEL JUSTICE"
Chuck
by conch
Wed Sep 04, 2019 8:45 am
Forum: The GAM
Topic: Towing Home My "Barn Find"
Replies: 9
Views: 11438

Re: Towing Home My "Barn Find"

The dive door just fits that well into the opening to look sealed and it still has all its original sealing rubber and clamps. I doubt it was ever used much. The original custom short bungee cords to hold/store the door when removed into two chocks on deck were still sealed in a bag in the owners po...
by conch
Tue Sep 03, 2019 5:41 pm
Forum: The GAM
Topic: Towing Home My "Barn Find"
Replies: 9
Views: 11438

Re: Towing Home My "Barn Find"

CW member MAVERICK had a beautiful restored 1987 18' GUARDIAN with DIVE DOOR that he sold here in the Marketplace around Oct of 2017. Search the listing for pics. I just was not ready yet. In hindsight after looking and operating both, I prefer the 21' Justice with a four stroke Yamaha F300 vs the E...