CONTINUOUSWAVE

Phil T

The part # have changed over the years.

From the thread -

"The Whaler part# for the blank panel with switches is 1848341".

Phil T

In looking around, I see Jay Heiii's 2007 Montauk 170 has the same exact panel.

See: http://continuouswave.com/forum/viewtopic.php?f=6&t=3981&p=22558

Phil T

While not exactly what you are thinking, consider this. You can use the existing panel and cover it with 3M Vinyl. Replace the switch "covers" with labels. Several owners have "refreshed" their panel without spending the $$. New Wire Marine sells switches and covers at reasonable...

Phil T

I did a little research on Whaler's Resources page of their website. For 2005, Montauk 170 there are two instrument panels shown: Screen Shot 2021-04-11 at 1.35.23 PM.jpg There are parts # 09 and #63 Part #09 is described as: Screen Shot 2021-04-11 at 1.33.30 PM.png Part #63 is described as: Screen ...

Phil T

It is not integral and can be removed.

Phil T

Ice out was early this year. Good for you.

Phil T

I would reach out to Ken or Dan.

Phil T

It is clear you are not on the right path.

Also, the engine should be mounted two- or three-holes up, top bolt in the third or fourth hole down from the top. This is why you are porpoising.

I recommend you go back and read my prior post.

Phil T

Instead of a two step hoist I described above, consider going with a spreader bar type setup. From each hoist would be two straps/wire cable to a spreader bar the legnth necessary to span the beam of the boat. From the each spreader bar a strap (with small weights) would fall from the end, down and ...

Phil T

Tony--my suggestion comes from watching the RNLI in the UK. They retrieve their Severn/Trent class rescue boats (14'm LOA, 28 tonne) by winching them up a long steep ramp via cable, then change to an industrial strap harness for the distance into a boat house. The strap is what keeps them secure.

Phil T

This is page 2

Phil T

I reached out to Don offline and he provided the factory instructions.

While it is a .pdf I saved it as a jpeg so it can be uploaded here.

Phil T

When I ran the numbers I got 18" of pitch. This is based on WOT of 6200, Target speed of 56, slip of 5% and gear ratio of 1.83

I presume Scott is trimming the engine out.

Phil T

Here are the pages from the manual. Screen Shot 2021-04-07 at 9.31.50 PM.jpeg Personally I would lift the boat with wire cables then position wide lifting straps slightly forward of the transom and a second aft of the bow and support the hull that way. The straps would be set at a fixed height and t...

Phil T

Glenn -

Review Don's comment in this identical thread:

http://continuouswave.com/ubb/Forum3/HTML/004007.html

Phil T

The CGP or BCPD boat market is challenging, even in good times. The Frontier, based on the Outrage 25 hull is smaller, lighter than the Challenger or Guardian 27. As for navigating between Miami to Nassau, Bahamas, the distance is 185-miles. For any boat, it is a matter of sea conditions, engines, a...

Phil T

I think you have the wrong version.

The flat annode is for twins or engines with hydraulic steering.

Call Andy at SIM Yamaha. They will get you sorted.

https://www.simyamaha.com/search.php?search_query=61A-45371-00-00%20&section=product

Phil T

If you can't get in the boat, even take it for a sea trial (weather is now nice). FORGET IT.

Would you spend $24,00 on a car you can't see in-person, get in and go for a test drive?

Phil T

Having done an inspection of two Challenger 27 boat, I am very smitten. Then again, it depends how you are going to use the boat. For cruising year round in the upper NW, Alaska or DownEast --> Challenger. For fishing, diving, freight, etc ---> Frontier. Demand is through the roof, the prices are ri...

Phil T

Scott--with the Enertia, the engine is 400-RPM under WOT 6200-RPM. I would say drop pitch by 2-inches. You may gain you another 2 to 3-MPH. Then again... Can the engine mounting go up a hole? Typically Mercury engine can go up one-hole higher than typical due to their midsection (per LHG), and hhenc...

Phil T

Propeller performance is not all about size. You need to take into account the make and the model of the propeller. From experience, a Montauk 17 with a 115-HP engine running light and mounted three-holes-up should be able to reach 49-MPH. What model year is the Mercury 115 Pro XS? The early version...

Phil T

One should not compare a 2011 Montauk 170 II (taller console version) to a Montauk 170 III (completely redesigned hull, interior fuel tank etc). Comparing apples to bulldozers. As for the 2011 Montauk 170 pricing. Condition Location (cheaper in FL,TX, more expensive in CA) Condition Bottom paint? El...

Phil T

If you are concerned about the prop, just buy a cage.

http://www.propguardtech.com/custom.html

Phil T

Keel Guard or similar products are added to the keel only rather than the chines. Most installations go five to six feet aft of the bow eye. Typically this is all that is necessary to beach a boat. When beaching my boat on the precast concrete planks covered in barnacles at the local boat ramp with ...

Phil T

Simon -

Look for these sizes

13.25x15 PowerTech SCP
13.25x15 Yamaha Performance Series
13.25x15 Turbo 1
13x17 Yamaha Painted Stainless Steel

This is the results from the prop size calculator.

: Screen Shot 2021-03-31 at 2.45.47 PM.png (25.36 KiB) Viewed 138 times

Phil T

Jack--sorry to surprise you but this is one of the worst times to repower. Due to COVID, demand for boats and new engines is off the charts. Boat production is already sold out for this year and part of next. Many owners expecting to just walk in and buy a new engine to re-power are waiting until fa...

Phil T

The 1997 Mercury 115-HP has a dry weight of 348 lbs.

Phil T

All the marinas I have visited in New England use floats of varying construction. They support boats in size from 15' to 250' super yachts (have a helicopter on the upper deck and/or tender inside the fantail). As for decking, if boards are required, composite materials. Other materials include stam...

Phil T

I find it highly surprising the new docks are fixed rather than floating. Given the variable level of the lake, it would, to me, be prudent to take this into account in the design. A future period of higher water levels will result in repeating the same damage as before. Steel piles and concrete flo...

Phil T

Please STOP confusing the hole location with the actual position of the motor. The motor position should NOT be taken into account. Get a measuring tape and MEASURE the holes. Look at the DIAGRAM with the distances and then measure to the locate the lower hole location. Mark it, then drill. If it is...

Phil T

You don't drill the holes to a fixed height. You drill the holes so that the engine can be adjusted in the future. Look at the diagram in the reference section. You are over thinking this. We recommend mounting the engine (not drilling) 2 holes up (bottom bolts in the slots), top bolt in the 3rd hol...

Phil T

Check all the through hull drain tubes. The originals were brass with rubber O rings.

Phil T

Check with Choates Boats.

He might have one.

https://www.choatesboats.net/

Phil T

Whaler Drives are not factored into the trailer length-over-all.

Phil T

Opinions on the steering cable range from 14' to 16'.

Review the bottom 4 posts on this thread: http://www.continuouswave.com/ubb/Forum3/HTML/000008.html

Phil T

K series is how Yamaha identifies its intermediate gearcase.

Yes--hat is the Performance Series prop.

I forgot to add my last propeller shop from which Boston Whaler owners have had good service and support:

Dan's Discount Props. https://dansdiscountprops.com/index.cfm

Phil T

Sorry about this. I am highly surprised Andy recommended an aluminum propeller for you. Many years of experience and testing here has resulted in the recommendation to never install an aluminum prop on an outboard larger than 40-HP. I stand by the Yamaha Performance propellers listed above. One coul...

Phil T

Contact Ken at http://www.Propgods.com for the PowerTech props

and

Andy at SIM Yamaha. http://www.simyamaha.com

Right handed rotation.

Do not substitute propeller model or size unless Ken or Andy say otherwise.

Phil T

Fish - The rubrail is two parts, a receiver and an insert. While you can order it from a local Boston Whaler dealer, or Barbour Plastics, I prefer to use either: Sue Lodel, Parts Manager Beacon Twin Cities Marine, WI http://www.beacontcm.com Justin -Associate Nauset Marine - MA http://www.nausetmari...

Phil T

You can simulate the change of engine weight by adding bags of gravel or sand to the splashwell. As for performance, you will probably have to change props with the engine change. Before I spend any money I would review your boat's current engine setup and rigging. I have a sense there are adjustmen...

Phil T

You may want to wipe down the rubrail insert with Acetone to see if it will come back.

Phil T

Splash boards should have two rectangular openings with hinged flap that only swings toward the stern.

Rough dimensions for an appropriate opening would be 4" high x 11" wide.

Phil T

Here are a few photos from the 1975-1978 catalogs courtesy of Tom Clark's Catalog collection.

: Fig. 2.; 1977.jpg (175.06 KiB) Viewed 911 times

: Fig. 3.; 1976.jpg (33.84 KiB) Viewed 911 times

: Fig. 4.; 1975.jpg (172.4 KiB) Viewed 911 times

Phil T

The photo of the Load Rite trailer above is my personal trailer. It is a Load Rite Elite - Model #18240096VT. It has a capacity of 2,400; Torsen Axle, 14" radial tires, 72" between fenders and an overall legnth of 20'4". https://www.loadrite.com/trailers/load-rite-galvanized-single-ax...

Phil T

Contact Dave/Doug at Lockman's, one of the oldest Evinrude dealers and a guru of older Johnson engines.

http://lockemans.com

Phil T

The F70 is the lightest in its class and is a very good candidate for the classic 16/17 models. A jackplate only assists if one transits "skinny" water on a frequent basis. The added weight does not improve wide-open-throttle (WOT) by much. Unless there is a truly compelling reason, skip i...

Phil T

While we will not be able to dial in your boat's performance exactly without a tachometer, a worthwhile prop to select is the BPR Enertia. Many Boston Whaler owners over the years have had very good results contacting Dan's Discount Props. They are very experienced in prop selection and understand B...

Phil T

I have owed two Load Rite Elite trailers, the second purchased 2 yrs ago. They are very good. The 5S- means it is a 5 Starr model. If you have tight storage location, go with galvanized. They have a shorter total-legnth-overall. Trailer prices are inflated due to covid. Expect to pay around $2,200 f...

Phil T

Price depends on condition, features, original elements and location.

Phil T

The photo above showing the blue rollers is more typical of European or Australian trailers which have rollers situated aft of the transom and slightly below and the welded frame rather than U bolt attachment method.

Search found 1645 matches