Search found 34 matches

by mikegcny
Mon Jul 18, 2022 11:30 am
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

This is what I came up with as to not interfere with the ski eye.

skiwee1-0001.jpg
skiwee1-0001.jpg (44.52 KiB) Viewed 2627 times
by mikegcny
Mon Jul 11, 2022 10:59 am
Forum: The GAM
Topic: 2022 Fuel Prices at Marina Fuel Docks
Replies: 11
Views: 2843

Re: 2022 Fuel Prices at Marina Fuel Docks

My marina in Cutchogue NY is charging [no price mentioned]. The fuel dock is busy.

[Please report the price if you want to participate in this thread that is collecting information on the price of fuel at the dock in the USA in Summer 2022.]
by mikegcny
Fri Jul 08, 2022 8:59 am
Forum: REPAIRS and MODIFICATIONS
Topic: Fuel Tank Fastening System Retrospective
Replies: 10
Views: 3015

Re: Fuel Tank Fastening System Retrospective

What do you suggest to protect the tank from the fiberglass and aluminum with other than rubber? Some people use [KING StarBoard] strips about two-inches wide that run athwart to the tank. They cut them about two-inches-short so that there is a small channel under the center of the tank for water t...
by mikegcny
Thu Jul 07, 2022 6:45 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Fuel Tank Fastening System Retrospective
Replies: 10
Views: 3015

Re: Fuel Tank Fastening System Retrospective

I was just doing some research on foam, and came across this site - http://www.uscomposites.com/foam.html "Once fully cured this foam can be laminated over with any type of polyester, epoxy or vinyl ester resin without melting." I wonder if instead of trying to glass over the tank and foam...
by mikegcny
Thu Jul 07, 2022 5:45 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

But I will have to caution that perhaps some experience with a pipe bender ought to be to obtained before attempting to bend a navigation pole lamp that cost several hundred dollars. That is really hard to do. My dad and uncle are both electricians and no matter how many times they show me, I can't...
by mikegcny
Wed Jul 06, 2022 11:18 am
Forum: REPAIRS and MODIFICATIONS
Topic: Fuel Tank Fastening System Retrospective
Replies: 10
Views: 3015

Re: Fuel Tank Fastening System Retrospective

Thank you for posting this information. ASIDE: I plan to replace my tank in Winter 2022-2023 I am still not sure if I should use foam or not. I am of the mindset that no matter what I do, water will always get to both the fuel cavity and under deck maze of tunnels. I like the approach of being able ...
by mikegcny
Wed Jul 06, 2022 11:00 am
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

Phil T wrote:Do you have the original light pole hardware for the transom?
There is only bottom stand off on the transom. The top one is missing.
by mikegcny
Wed Jul 06, 2022 9:21 am
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

Probably $500 now. That is what I am trying to avoid. ski wee.jpg I might add a vertical pole to the fiberglass seat back next to the ski pylon. Maybe even something that folds flat that can be out of the way. I am realizing now that where the ski pylon is mounted, having the lamp anchored to the t...
by mikegcny
Tue Jul 05, 2022 6:49 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

jimh wrote:Why are you concerned with the bend angle in the pole?
I want the one I order to sit in correct orientation to the water. Perko makes lots of different options for angles.
by mikegcny
Tue Jul 05, 2022 1:20 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Re: Navigation Pole Lamp Bend Angle

Figure 1 shows the OEM lamp with the [bend in the pole] highlighted

bend.jpg
Fig. 1. A pole lamp with a bend whose angle to be determined by readers of this post.
bend.jpg (10.62 KiB) Viewed 2853 times
by mikegcny
Tue Jul 05, 2022 11:48 am
Forum: REPAIRS and MODIFICATIONS
Topic: Navigation Pole Lamp Bend Angle
Replies: 16
Views: 2877

Navigation Pole Lamp Bend Angle

What is the angle [of the bend in the pole that held] the all-round white light pole lamp on a 1988 SUPER SPORT LIMITED 13?

I want to install a new all-round white navigation lamp on a pole.
by mikegcny
Fri Jul 01, 2022 12:06 am
Forum: REPAIRS and MODIFICATIONS
Topic: Outrage 22 Modifications - Electrical and Console
Replies: 1
Views: 1072

Outrage 22 Modifications - Electrical and Console

Thought I would share this album of my modifications I made in the spring of 2021. https://photos.app.goo.gl/Kk7h6DcucgE4QwLUA 1984 Boston Whaler Outrage 22 Project Details Electronics / Electrical ⋅  100% all new wiring (with the exception of the Yamaha rigging) ⋅  New fuse pane...
by mikegcny
Thu Jun 30, 2022 6:32 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Outrage 22: Wood Locating Diagram
Replies: 0
Views: 2839

Outrage 22: Wood Locating Diagram

Looking for the wood location diagram for a 1984 Outrage 22.

As a corollary - do the 'stringers' that are under the deck (where the deck outermost deck plate screws go into) have wood in them?
by mikegcny
Tue Apr 27, 2021 12:04 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Fuel Inlet Filler Cap
Replies: 3
Views: 3116

Fuel Inlet Filler Cap

Where can a replacement fuel filler cap for my 1984 OUTRAGE 22 be purchased? fuelFillerCap.jpg The fitting has a square housing. I only need the cap. I do not want to replace the entire housing unless the replacement part is a 100-percent match to the original part. The replacement cap does not need...
by mikegcny
Fri Apr 16, 2021 12:58 pm
Forum: The GAM
Topic: Teak Door Recssed Opening Size
Replies: 0
Views: 5790

Teak Door Recssed Opening Size

What are the dimensions of the rounded rectangular recess opening see below in FIgure 1?
Door.jpg
Fig. 1. A teak door with whose opening dimensions are sought, inferred to be from a 1984 OUTRAGE 22 boat.
Door.jpg (26.11 KiB) Viewed 5790 times


BACKSTORY: My boat 1984 Outrage 22 and it console doors are not at my current location, and I cannot measure.
by mikegcny
Wed Apr 14, 2021 10:29 am
Forum: REPAIRS and MODIFICATIONS
Topic: Super Console Drawings or Photographs
Replies: 0
Views: 5639

Super Console Drawings or Photographs

I am looking for a drawing or photo of the interior of the SUPER CONSOLE that was used in c.1984. That console is an early design and is more flat and more square than later Super Console designs. I need to see the configuration of the factory shelf and drawer. Additionally, in my boat there is a sp...
by mikegcny
Tue Apr 13, 2021 2:27 pm
Forum: REPAIRS and MODIFICATIONS
Topic: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:
Replies: 7
Views: 3313

Re: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:

...by switches [moving to the recess where the fire-extinguisher was] I mean the engine battery selector switches and house battery switch. Any electrical switch should be protected from spray and splash. The sides of the console seem more vulnerable than the dashboard area. Perhaps a hinged clear ...
by mikegcny
Tue Apr 13, 2021 1:59 pm
Forum: REPAIRS and MODIFICATIONS
Topic: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:
Replies: 7
Views: 3313

Re: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:

How would you access those switches while piloting the boat at the helm? The usual location for any electrical switch at the helm is to be in reach of the helmsman while at the wheel. By switches I mean the engine battery selector switch and house battery switch. I have a new custom switch panel fo...
by mikegcny
Tue Apr 13, 2021 1:56 pm
Forum: REPAIRS and MODIFICATIONS
Topic: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:
Replies: 7
Views: 3313

Re: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:

jimh wrote:
shows that the access hole in the deck through which engine rigging and other cables pass DOES NOT have the usual surrounding raised plastic shield or water dam to keep water from entering the rigging tunnel.

That is all being rebuilt with KING StarBoard.
by mikegcny
Tue Apr 13, 2021 1:09 pm
Forum: REPAIRS and MODIFICATIONS
Topic: OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:
Replies: 7
Views: 3313

OUTRAGE 22 SUPER CONSOLE: Moving Batteries to Center Console:

I am thinking of moving the batteries to the [SUPER CONSOLE on an OUTRAGE 22 boat] console. Give input. BACK STORY: A piece of teak broke on my console in 2020.. Rather than just fixing it, I decided to re-do the entire console with all new teak, wiring, hardware, and switches. I also relocated thin...
by mikegcny
Mon Sep 23, 2019 5:30 pm
Forum: PERFORMANCE
Topic: Super Sport Limited - 40 HP
Replies: 4
Views: 8293

Re: Super Sport Limited - 40 HP

How old are the kids? A 40-MPH boat is very fast for a 13-footer. They will be 13 and 10 next summer. We won't let them use it by themselves until they are a little older, have taken the Power Squadrons class, and have demonstrated to us that they are responsible. The Outrage 22 that we have is not...
by mikegcny
Mon Sep 23, 2019 3:32 pm
Forum: PERFORMANCE
Topic: Super Sport Limited - 40 HP
Replies: 4
Views: 8293

Super Sport Limited - 40 HP

I am buying a 1988 13 Super Sport Limited for my kids to use next summer. It has a 2001 Mercury 40-HP. Hull is 1988 13' Super Sport Limited.

How fast will this boat be?
by mikegcny
Tue Jul 03, 2018 2:50 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Redgard
Replies: 4
Views: 3354

Re: Redgard

There are some spots that were pretty soggy. I'm not even certain that I can get to it next winter.

Thought it would buy me some time.
by mikegcny
Tue Jul 03, 2018 12:29 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Redgard
Replies: 4
Views: 3354

Redgard

Have a 1984 Outrage 22'. I pulled the rear deck over the live well. Deck is not soft, but the wood is starting to get wet. I don't have the time to chisel out the wood, replace it then glass it in.

Does anyone think that lining the bottom of the deck in Redgard would work?
by mikegcny
Sat Sep 09, 2017 9:45 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1984 Outrage 22 - Tunnel and Live Well Work
Replies: 4
Views: 3118

Re: 1984 Outrage 22 - Tunnel and Live Well Work

I did all the modifications to the boat today. I dressed all the wires in the rigging tunnel to make it easier to get the pumps installed, wired, and connect hoses. I hope everything will be dry tomorrow so I can test it out.
by mikegcny
Thu Sep 07, 2017 7:54 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1984 Outrage 22 - Tunnel and Live Well Work
Replies: 4
Views: 3118

Re: 1984 Outrage 22 - Tunnel and Live Well Work

Thanks for the advice Jim. For some reason on mine there is no drain tube between the port and starboard tunnels. I currently have an 1,100-GPH pump in the starboard well (the area you described) and although the automatic mode doesn't work, it performs well. I am going to try out a 2,000-GPH in the...
by mikegcny
Tue Sep 05, 2017 9:46 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1984 Outrage 22 - Tunnel and Live Well Work
Replies: 4
Views: 3118

1984 Outrage 22 - Tunnel and Live Well Work

I have been fishing often this season and, as I am sure most of you know, the open transom of the Outrage 22 allows in quite a bit of water. Earlier in the season I was contemplating building the transom up with KING Starboard. Since I have twin engines such a system would not work that well and, in...
by mikegcny
Wed Aug 23, 2017 9:34 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Outrage 22: Remote Control Cable Lengths
Replies: 2
Views: 2263

Re: Outrage 22: Remote Control Cable Lengths

I have the same console with twins. My throttle cables are 21ft on the port, 19ft on the starboard.

I replaced my control cables but don't have an electronic receipt to check.
by mikegcny
Thu Aug 10, 2017 3:39 pm
Forum: The GAM
Topic: Make a Guess About New Boats
Replies: 6
Views: 5104

Re: Make a Guess About New Boats

A return to blue interiors and teak.
by mikegcny
Mon Aug 07, 2017 11:45 pm
Forum: The GAM
Topic: Recall Your First Time In a Boston Whaler
Replies: 13
Views: 9749

Re: Recall Your First Time In a Boston Whaler

My first time was in my 1988 Montauk. My dad always had Sea Rays and would always point out Whalers, Gradys and Wellcrafts to my brother and I. When I was 12 my dad upgraded to a larger Sea Ray that we could no longer ski off of. One day in the fall of 1988 he took my brother an I "for a ride&q...
by mikegcny
Tue Aug 01, 2017 10:28 am
Forum: The GAM
Topic: 1996 Outrage 22
Replies: 9
Views: 7220

Re: 1996 Outrage 22

So then this most likely is a 1996 - special order. I think 93 was the last year of the 22.
by mikegcny
Tue Aug 01, 2017 10:19 am
Forum: PERFORMANCE
Topic: 1984 Outrage 22 Re-power
Replies: 3
Views: 3961

Re: 1984 Outrage 22 Re-power

I have twin F115s on the same boat (84 Outrage 22 with the Super Console). It does have a bit of squat that I am going to correct by moving the console forward about 10 inches and moving the batteries up to the console. I should also mention that my boat was originally a cuddy, so the console is abo...
by mikegcny
Mon Jul 31, 2017 11:35 am
Forum: The GAM
Topic: 1984 Outrage 22
Replies: 2
Views: 2680

1984 Outrage 22

I got my boat cleaned up and the rub rail reattached last week. I spent a whole day compounding, polishing and waxing the hull. I think it came out great. We finally got to do some fishing. My brother stopped by in his 88 Montauk that he just had re-powered. It is the same boat that my dad bought ne...
by mikegcny
Mon Jul 31, 2017 10:58 am
Forum: The GAM
Topic: 1996 Outrage 22
Replies: 9
Views: 7220

Re: 1996 Outrage 22

I am on LI - saw this on CL.

Did you happen to see it last weekend? Do you have any pictures of the splashwell? The spalshwell can help date the hull.