Search found 34 matches
- Wed Aug 28, 2019 6:52 am
- Forum: PERFORMANCE
- Topic: 1988 Outrage 22 Whaler Drive E-TEC 200 H.O.
- Replies: 4
- Views: 7741
Re: 1988 Outrage 22 Whaler Drive E-TEC 200 H.O.
Read my prior discussion at OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O. http://continuouswave.com/forum/viewtopic.php?f=7&t=3521 My [OUTRAGE 22 Whaler Drive boat] does not have bottom paint, a T-top, or a bait tank. My boat also has an E-TEC G2 225 H.O. and thus more horsepower. Results from my p...
Re: XD50 Oil
I was using XD50 in my old 1989 Evinrude 225 engine, and I was not pre-mixing the oil into the gasoline. I noticed no ill effects from use of XD50.. When I changed to XD50 from XD30 I noticed less smoke at start-up. I have upgraded my engine and use exclusively XD100 now. I hope this information is ...
- Thu Sep 13, 2018 7:54 am
- Forum: PERFORMANCE
- Topic: 2007 Outrage 24 Re-power with Single from Twins
- Replies: 7
- Views: 12050
Re: Repower 2007 Outrage 24
I recently re-powered an Outrage 22 Whaler Drive with a single E-TEC G2 225 H.O. My boat will do 44-MPH conservatively; the highest speed seen 47.1 MPH running downwind. Jim H has a 225 G1 on his Revenge 22 W-T Whaler Drive, and in a recent post had a top speed of 43.5 MPH. I would expect similar re...
- Tue Aug 07, 2018 2:14 pm
- Forum: REPAIRS and MODIFICATIONS
- Topic: Bunk Glides
- Replies: 2
- Views: 2790
Re: Bunk Glides
My trailer has plastic-cap-type slide over the carpet. I have not noticed any damage to the gel coat that I could attribute to the bunk slicks.
Bruce
Bruce
- Sat Jul 07, 2018 5:02 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Picked up a REBEL TBX 17-pitch yesterday at the dealer. The boat was more heavily loaded today approximately 60 gallons of fuel, and 4 passengers, versus the one passenger in the last testing. Two of the additional passengers were novice boaters and did not like the speed, so these are initial numbe...
- Thu Jul 05, 2018 6:31 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
The Cyclone 15-pitch propeller did not have enough pitch. Pushing the throttle toward wide open, the motor hit 6,000-RPM, boat speed was around 42-MPH, and I had more throttle to go--so I pulled back. Back to the dealer today to explore more options. We did spend a nice day on Casco Bay and had a gr...
- Tue Jul 03, 2018 12:43 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Phil--thank you for adding these pictures for me.
I just returned from the dealer. They did not have a REBEL 15-pitch or 17-pitch. I have a CYCLONE four-blade 15-pitch to try out.
Running the boat tomorrow will post initial numbers then--Bruce
I just returned from the dealer. They did not have a REBEL 15-pitch or 17-pitch. I have a CYCLONE four-blade 15-pitch to try out.
Running the boat tomorrow will post initial numbers then--Bruce
- Sat Jun 30, 2018 7:39 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Ran the boat for the past few days. The Evinrude E-TEC G2 225 H.O. needs less propeller pitch. Right now the prop is an RX4 18" pitch. The maximum speed the engine could accelerate to was 5310-RPM, and boat speed was 46.5-MPH. The boat was porpoising; when I trimmed down to stop porpoising, eng...
- Sat Jun 30, 2018 7:37 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Jim--that is the correct thread I was quoting. I admire your carefully measured and [annotated] photographs of your old engine mounting height. I will attempt to take some careful measurements and photos of my new G2 225 H.O. that may illustrate some of the differences between the mounting of these ...
- Tue Jun 26, 2018 8:16 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
This was a cut and paste from the old forum, same thread as the above cut and paste; the original thread was from 2011: I made it out for testing/fishing yesterday. My new average top speed is 44=MPH (1 run with wind 1 against). There are no negative effects that I noticed yet. No ventilation or blo...
- Tue Jun 26, 2018 6:34 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
The old engine was mounted three-holes-up.
- Sun Jun 24, 2018 8:50 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
The following is a cut and past from an earlier thread on the mounting height of my old outboard. I will make an effort to clarify my statements. There are 4 holes in the upper mounts to my motor. My motor is now mounted in the lowest hole (all the way up). Before Saturday the motor was mounted in t...
- Sun Jun 24, 2018 8:35 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Jim--the old motor 1988 Evinrude 225 HP was mounted in the lowest hole available. It was mounted as high on the transom as I could mount it unless I added a jack plate. I do not have the old motor any longer so I can't count the mounting holes available. I have requested that the new motor Evinrude ...
- Thu Jun 21, 2018 6:32 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: OUTRAGE 22 Whaler Drive Propeller
Jim That was my thought and the dealer has told me that if the prop is not correct they will swap for different pitch at no cost ( assuming no prop damage).
El Rollo I have reached out to a friend and asked if he would help me with some before and after photo's after the install is completed.
Bruce
El Rollo I have reached out to a friend and asked if he would help me with some before and after photo's after the install is completed.
Bruce
- Tue Jun 19, 2018 2:51 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: 22' outrage WD prop selection
Phil, The old motor is "all the way up" and I have asked Bamforth's to mount the new one the same. I have not experienced any negative affect of the higher mounting height with the old motor. The owner of Bamforth's assured me that the new G2 outboards would tolerate a higher mounting heig...
- Tue Jun 19, 2018 1:58 pm
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: 22' outrage WD prop selection
Gentlemen
Thanks for the quick response, that is the same model and pitch that was recommended for me.
Bruce
Thanks for the quick response, that is the same model and pitch that was recommended for me.
Bruce
- Tue Jun 19, 2018 11:48 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
Re: 22' outrage WD prop selection
Thanks Phil,
I have read most of JimH's reports but I'm not sure the RX4 props were available when he tested
Bruce
I have read most of JimH's reports but I'm not sure the RX4 props were available when he tested
Bruce
- Tue Jun 19, 2018 10:53 am
- Forum: PERFORMANCE
- Topic: OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
- Replies: 27
- Views: 17710
OUTRAGE 22 Whaler Drive, E-TEC G2 225 H.O.
Gents—I will be re-powering my Outrage 22 Whaler Drive with an E-TEC G2 225 H.O. The dealer has recommended an Evinrude RX4 15 x 18-pitch propeller and has carried that propeller in the quote. I currently have a 1988 Evinrude 225 that used push the boat to 41 to 42 MPH with a 15-pitch Stiletto prope...
- Fri Oct 06, 2017 9:30 am
- Forum: The GAM
- Topic: Evinrude G2 DPS
- Replies: 1
- Views: 2431
Evinrude G2 DPS
I may be re-powering my boat in the next year or so. I would like to install an Evinrude G2 225 H.O. or 300--still undetermined--however, I use my boat to troll with a kicker quite a lot, probably 60% or more of total hours per year. I have seen that the G2 has an option for an auxiliary motor steer...
- Fri Sep 22, 2017 6:44 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225 No Spark
Thanks Jim
I will check this area thoroughly.
Bruce
I will check this area thoroughly.
Bruce
- Wed Sep 20, 2017 8:29 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225 No Spark
Update on this ongoing saga. With the help of a mechanc I have replaced: --the flywheel (used replacement) --timer base (new part) --stator (new part) --power pack (new part), and --rectifier (a known good used part). Still no spark. The ignition key switch and safety lanyard switch check out good. ...
- Tue Sep 05, 2017 6:40 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225 No Spark
Alan--thanks for the picture. My failure was not that dramatic, but I was able to see the metal ring I was asking about. It is affixed to the underside of the flywheel. I believe that a small portion of the broken magnet that I referenced was caught between the rotating parts and the stationary part...
- Fri Sep 01, 2017 8:49 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225 No Spark
Thanks for the responses. Jim I have the service manual. I should have added that the damage I noted is physical. I did perform resistance testing on the stator and one of the coils was well out of specification, like double or more the resistance it should have been, the manual has plus or minus 10...
- Thu Aug 31, 2017 11:04 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225
I have since removed the Flywheel, and there is a broken magnet. Apparently the fragments of the magnet contacted the stator damaging it, they also appear to have gotten into the timer base assembly and caused physical damage there as well. There is a small ring of metal with three narrow slots in i...
- Thu Jul 06, 2017 12:07 pm
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
Re: 1989 Evinrude 225
Thanks Guys I will proceed with caution.
- Wed Jul 05, 2017 8:53 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: 1989 Evinrude 225 No Spark
- Replies: 14
- Views: 10704
1989 Evinrude 225 No Spark
I have an electrical problem with my 1989 Evinrude 225 outboard engine. The other day while warming up the engine quit unexpectedly. There is no spark on any cylinder, I have verified that the key switch and the safety lanyard switch are not the problem by following the test procedures in my manual....
- Fri Jun 16, 2017 6:34 am
- Forum: PERFORMANCE
- Topic: Outrage 22 Whaler Drive Re-Power
- Replies: 9
- Views: 8714
Outrage 22 Re-Power
I realize this is an old thread. I am curious [to hear news about the boat re-power that was being discussed several months ago].
I have a 1989 [OUTRAGE 22 Whaler Drive] with its original Evinrude 225-HP outboard engine. I am sure a re-power is not too far in the future for me. --Bruce
I have a 1989 [OUTRAGE 22 Whaler Drive] with its original Evinrude 225-HP outboard engine. I am sure a re-power is not too far in the future for me. --Bruce
- Wed Mar 29, 2017 9:09 am
- Forum: REPAIRS and MODIFICATIONS
- Topic: Converting a Single-axle Trailer to Two-Axle
- Replies: 3
- Views: 3033
Re: Converting a Single-axle Trailer to Two-Axle
Phil, Thanks for the reply, give your family my best as well. I believe the axle manufacturer will provide minimum axle spacing for dual applications. The trailer does not "need" dual axles, but I haul it on the golden road, and telos road, so I want the redundancy of dual axles. The trail...
- Tue Mar 28, 2017 3:56 pm
- Forum: REPAIRS and MODIFICATIONS
- Topic: Converting a Single-axle Trailer to Two-Axle
- Replies: 3
- Views: 3033
Converting a Single-axle Trailer to Two-Axle
If I wished to add an axle to a trailer, should I just find the center of the existing axle, then using appropriate spacing move one axle forward half that distance and the other rearward the other half of the distance? Or are there other things that I am not thinking of? The trailer currently is to...
- Mon Jan 09, 2017 8:22 am
- Forum: PERFORMANCE
- Topic: FreeValve Engine
- Replies: 3
- Views: 3999
Re: FreeValve Engine
I believe Formula-1 [racing] has been experimenting and testing this technology. The valves in F-1 engines have been using pneumatic "springs" for a while.
Bruce
Bruce
- Tue May 24, 2016 3:03 pm
- Forum: PERFORMANCE
- Topic: Trolling with Auxiliary Engine
- Replies: 6
- Views: 5912
Re: Trolling with Auxiliary Engine
Jim's math proved to be very accurate. Idle speed with 7-pitch propeller installed was 0.8-MPH on the GPS in calm conditions. This is the speed that I was looking for. Obviously in windy conditions I may still need to use something for drag to slow the boat. I am satisfied with this set up. Thanks f...
- Wed May 11, 2016 8:49 am
- Forum: PERFORMANCE
- Topic: Trolling with Auxiliary Engine
- Replies: 6
- Views: 5912
Re: Trolling with Auxiliary Engine
Phil--yes. Inland lakes for landlocked salmon, Rangeley, Sebago, Sebec, Richardson, I may have to resort to the drift sock but I'm exploring options. Good to hear from you again. Thanks again for the help with the trailer . The trailer is still running great. It was fun to meet another forum member....
- Tue May 10, 2016 7:14 am
- Forum: PERFORMANCE
- Topic: Trolling with Auxiliary Engine
- Replies: 6
- Views: 5912
Re: Trolling with Auxiliary Engine
Thanks Jim and Kwik
I have never observed the prop on the main motor while trolling but I will try engaging reverse and see if that helps
Bruce
I have never observed the prop on the main motor while trolling but I will try engaging reverse and see if that helps
Bruce
- Mon May 09, 2016 8:33 am
- Forum: PERFORMANCE
- Topic: Trolling with Auxiliary Engine
- Replies: 6
- Views: 5912
Trolling with Auxiliary Engine
I am trying to find an alternative to rigging drift socks to the front of my boat to reduce trolling speeds at idle to 0.7 to 0.8-MPH from around 1.1-MPH. The general consensus on fishing forums seems to be to rig a drift sock off the front of the boat. I am not sure that I want the sock, or the har...