Search found 2602 matches

by Phil T
Wed Aug 16, 2023 9:15 pm
Forum: PERFORMANCE
Topic: 130 SPORT with 40-HP
Replies: 14
Views: 2570

Re: 130 SPORT with 40-HP

I would want to verify the gear ratio of the current Mercury 40 is the same. They occasionally change.

The new 130 SuperSport is heavier than your model.

I would try the Spitfire in that lower pitch I suggested.
by Phil T
Wed Aug 16, 2023 6:52 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Engine Water Pressure Drops with Engine Speed Increase
Replies: 16
Views: 8444

Re: Engine Water Pressure Drops with Engine Speed Increase

Make sure the impeller was installed correctly. There is an orientation to them.
by Phil T
Mon Aug 14, 2023 3:08 pm
Forum: The GAM
Topic: Boat for Boston Harbor, New England Coast
Replies: 11
Views: 2654

Re: Which boat for boston harbor and new england coast?

While the modern 150 has a better hull design and rides smoother, the shorter LOA degrades the ride in rougher conditions. To limit towing to a Pilot (5,000lb) limit I would suggest, in order of preference: 1 - Outrage 17 II (1996-1999) 1700lb hull 2 - Outrage 17 I (1990-1995 1050lb hull 3 - Montauk...
by Phil T
Mon Aug 14, 2023 1:21 pm
Forum: The GAM
Topic: Boat for Boston Harbor, New England Coast
Replies: 11
Views: 2654

Re: Boat for Boston Harbor, New England Coast

For the New England coast, the models you listed are very small and will severely limit the days that are comfortable to go out. The afternoon southerly breeze kicks up and the sea state can deteriorate. Fast. You really pay the price when in a short length overal (LOA) boat. Two feet LOA makes a wo...
by Phil T
Mon Aug 14, 2023 1:03 pm
Forum: PERFORMANCE
Topic: 130 SPORT with 40-HP
Replies: 14
Views: 2570

Re: 130 SPORT with 40-HP

With elevation comes reduced atmospheric pressure and combustion engines suffer performance degradation. Electronic fuel injected motors experience less drop than carburated engines. At 5100 ft above sea level you loose 6.1 horsepower. The 40hp is now a 33.9 hp engine. The Black Max 14 pitch came wi...
by Phil T
Sun Aug 13, 2023 7:32 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1991 OUTRAGE 17 Transom “Disk” Purpose
Replies: 5
Views: 1968

Re: 1991 OUTRAGE 17 Transom “Disk” Purpose

[The disk on the transom of the 1991 OUTRAGE 17] is part of the grounding system for the fuel tank. There is a wire with green insulatoion that goes from the fuel fill to the fuel tank and then a second wire that leads overboard to an [electrode] that is under the waterline. You can replace [the bro...
by Phil T
Sun Aug 13, 2023 5:49 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2001 Mercury 90 Will Only Run at Idle Throttle
Replies: 4
Views: 1982

Re:2001 Mercury 90 Will Only Run at Idle Throttle

Start with the cables.

Pull the cover and inspect the end of the throttle cable. Then check the cable end at the remote throttle control.
by Phil T
Sun Aug 13, 2023 5:47 pm
Forum: The GAM
Topic: 190 NANTUCKET Seats
Replies: 4
Views: 2125

Re: 190 NANTUCKET Seats

You can obtain the rear seat cushion bottom and backrest from Andersons Mfg. They are an OEM quality vendor.

http://www.amfg.us/about-us

Give Tena a call.
by Phil T
Sun Aug 13, 2023 11:31 am
Forum: The GAM
Topic: 190 NANTUCKET Seats
Replies: 4
Views: 2125

Re: 190 NANTUCKET Seats

If you only need moderate cooling and decent seating, go with the cost effective classic Igloo Marine Elite cooler. This is sized for the OEM cushions from Anderson Mfg. Note this is NOT the new redesigned cooler series. https://www.westmarine.com/igloo-54-qt.-marine-elite-cooler-19991124.html Note ...
by Phil T
Sun Aug 13, 2023 11:26 am
Forum: MARKETPLACE
Topic: Appraisal: 1978 MONTAUK
Replies: 4
Views: 2273

Re: Appraisal: 1978 montauk

Without knowing location, I appraise the boat selling for $6,000 to $8,000.

In California the boat could sell for a bit higher price, and in Florida sell for a bit less.
by Phil T
Sun Aug 13, 2023 11:24 am
Forum: MARKETPLACE
Topic: FS: 1985 OUTRAGE 18 $30,000 Alexandria, Virginia
Replies: 2
Views: 2137

Re: FS: 1985 OUTRAGE 18 $30,000 Alexandria, Virginia

The market will be slow to respond to that asking price.

For that money, the teak/mahogany would be pristine, gelcoat shiny, OEM cushions from Anderson's Mfg. and an engine that is less than 10 years old.

Post photos that show that and you will have some bites.
by Phil T
Fri Aug 11, 2023 2:54 pm
Forum: PERFORMANCE
Topic: 2004 220 DAUNTLESS VERADO 225
Replies: 25
Views: 7319

Re: 2004 220 DAUNTLESS VERADO 225

If you look at the factory test, the weather is typically tropical, no wind, no current, no waves, very little fuel, no water, no gear or equipment. One person and no bottom paint. Q5: Are you running premium fuel? The bottom paint and fuel can easily explain the difference. That engine hour report ...
by Phil T
Fri Aug 11, 2023 12:04 pm
Forum: The GAM
Topic: Boat for Long Island Sound: c.2002 230 OUTRAGE
Replies: 25
Views: 3523

Re: Boat for Long Island Sound: c.2002 230 OUTRAGE

You really should do a comprehensive sea trial when purchasing a boat that substantial.

Hopefully you can find some poor conditions to give you a sense of how she handles in the snot.
by Phil T
Thu Aug 10, 2023 3:15 pm
Forum: The GAM
Topic: Boat for Long Island Sound: c.2002 230 OUTRAGE
Replies: 25
Views: 3523

Re: Boat for Long Island Sound: c.2002 230 OUTRAGE

Unless you plan on servicing the engine yourself assess which, if any, local dealers service E-TEC engines.

Many dealers have ended service of E-TEC engines as a matter of principle--very short sighted if you ask me.
by Phil T
Thu Aug 10, 2023 11:39 am
Forum: REPAIRS and MODIFICATIONS
Topic: 2004 255 Conquest Hatch Repair
Replies: 2
Views: 1723

Re: 2004 255 Conquest Hatch Repair

ammarineli wrote:Q2: is my proposed method a good method?
The repair technique you describe is appropriate for the hatches.

If the hatches that are not failing have a green line indicating exposed fiberglass, give them a thin coat of sealant to prevent them absorbing moisture.
by Phil T
Wed Aug 09, 2023 11:41 am
Forum: The GAM
Topic: Frequently and Infrequently Asked Questions: Hull Identification Numbers; Conformance Markings
Replies: 12
Views: 2563

Re: Frequently and Infrequently Asked Questions: Hull Identification Numbers; Conformance Markings

Ivo - You can get authentic reproduction capacity plate and the HIN plate from Magic Brush in the US state of Florida. She will authenticate your hull with the factory and produce the accurate plate and tag. Request the metal plate not the decal option. She made a set for me. She ships international...
by Phil T
Tue Aug 08, 2023 7:01 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Removing Water From Fuel Tank Cavity Drain
Replies: 2
Views: 1960

Re: Removing Water From Fuel Tank Cavity Drain

For all models that include a below deck fuel tank, the bottom of the tank cavity is below the level of the bilge. The only model I can think of where it is practical to install a drain tube in the aft wall of the fuel cavity is the 1984-1989 Revenge 22 and 25 with the aft fish well. Several members...
by Phil T
Tue Aug 08, 2023 6:49 pm
Forum: The GAM
Topic: Boat for Casco Bay, Maine
Replies: 2
Views: 1940

Re: Boat for Casco Bay, Maine

Having lived on Casco Bay for more than ten years and transited the waters eight months, March to October, every year, my perspective is that despite the geography and barrier islands, Casco Bay is rarely calm and is frequently crappy. There are short wind-created waves, intermittent ocean swells, c...
by Phil T
Fri Aug 04, 2023 11:56 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1991 Outrage 17 Sump Pump
Replies: 16
Views: 3114

Re: 1991 Outrage 17 Sump Pump

Your 1991 OUTRAGE 17 boat has been really messed with. The console switches [see Figure 1 above] are not original. The method of energizing the rear is obtuse. I would not like it and would re-wire the switches so they are energized at the console only as most owners have done. The livewell pump wil...
by Phil T
Thu Aug 03, 2023 2:52 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 16-footer Hull Paint Scheme
Replies: 2
Views: 1954

Re: 16-footer Hull Paint Scheme

The hull and deck colors are not paint; they are tinted gel coat resin. As for the original color scheme, you should detail the outside gunwales and interior to remove the oxidation and bring back the reflection. Owners are shocked to see the color and visual improvement in compounding the boat. If ...
by Phil T
Thu Aug 03, 2023 2:20 pm
Forum: PERFORMANCE
Topic: 1980 OUTRAGE V-20 with 250-HP
Replies: 2
Views: 2039

Re: 1980 OUTRAGE V-20 with 250-HP

The V-20 is sensitive to porposing as outlined in the reference article from Sal Mercurio's owner testimonial. See https://continuouswave.com/whaler/reference/V20Outrage/ I think with proper engine mounting (three-holes up from lowest, as high as possible) and a good stern lifting propeller, you sho...
by Phil T
Thu Aug 03, 2023 2:14 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Electrical Switch
Replies: 6
Views: 2341

Re: Electrical Switch

The original dash switches for the Outrage 17 I were push-pull Cole Hersee switches. Through the years, owners have upgraded switches to include rocker style. A good vendor of switches and panels is http://www.newwiremarine.com Many Whaler owners have used them and I highly recommend them for their ...
by Phil T
Thu Aug 03, 2023 2:08 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1991 Outrage 17 Sump Pump
Replies: 16
Views: 3114

Re: 1991 Outrage 17 Sump Pump

The 1990-1995 Outrage 17 I is a unique model in that it has a sump that is well below the waterline and it is not recommended to run the boat with the sump drain plug left open. A bilge pump is recommended for this and other reasons. While there are deck drains in the transom, on the 1991 model the ...
by Phil T
Thu Aug 03, 2023 1:58 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1991 Outrage 17 Sump Pump
Replies: 16
Views: 3114

Re: 1991 Outrage 17 Sump Pump

The bilge pump is located in the stern sump. Walk aft, pull the cover to the baitwell. Remove the tub insert. Looking straight down, the pump should be in the lower level (left) of the sump. It could have a separate float switch or one that is integrated into the pump. The bilge switch is either a t...
by Phil T
Wed Aug 02, 2023 9:52 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2001 E-Z-LOADER Trailer Replacement Spring Hanger
Replies: 3
Views: 1886

Re: 2001 E-Z-LOADER Trailer Replacement Spring Hanger

From reviewing the EZ Loader parts available, it appears the assembly can be made up by seperate comonents.

https://www.easternmarine.com/search/hanger%20bracket?brand=205
by Phil T
Wed Aug 02, 2023 9:26 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2001 E-Z-LOADER Trailer Replacement Spring Hanger
Replies: 3
Views: 1886

Re: 2001 E-Z-LOADER Trailer Replacement Spring Hanger

Given the importance of this piece of hardware, I would not trust welding as it requires the removal of the galvanization. The galvanization material is highly toxic. Also note that the galvanization process penetrates the metal so its full removal is highly difficult. Welding requires the proper ma...
by Phil T
Sat Jul 29, 2023 12:07 pm
Forum: PERFORMANCE
Topic: TENDER 11 Four-stroke-power-cycle Engine
Replies: 7
Views: 2128

Re: 4 stroke power for 11’ tender

Check the weigh of the 15 and 20 and then add the additional weight to what you have in the boat.

You may find you need to shop across brands to find the least heavy.

Shop dealers hard, prices vary a lot.
by Phil T
Fri Jul 28, 2023 1:24 pm
Forum: The GAM
Topic: Assessing Hull with Unusual Cracking
Replies: 10
Views: 2397

Re: Assessing Hull with Unusual Cracking

Remember these boats are hand made. The photo above shows gelcoat spider cracking that is typically found on curving or corner surfaces when it was applied too thickly and has dried out due to exposure. It is cosmetic. Detailing the gelcoat and removing the oxidation will lessen the visual sign of t...
by Phil T
Fri Jul 28, 2023 1:19 pm
Forum: The GAM
Topic: 2000 Outrage 18 Fuel Tank Replacement
Replies: 7
Views: 2424

Re: 2000 Outrage 18 Fuel Tank Replacement

This model was only produced for 1 year, 2000.

The boat with only 135-HP is underpowered based on the published hull weight of 2,500-lbs and the experience with other models. I would expect a 175-HP or 200-HP engine would be appropriate.

Outrage_180.jpg
Fig. 1. Reproduction of catalogue page
Outrage_180.jpg (174.87 KiB) Viewed 2390 times
by Phil T
Fri Jul 28, 2023 1:06 pm
Forum: REPAIRS and MODIFICATIONS
Topic: For a 1994 16 SL: Add T-Top or Canvas Top
Replies: 2
Views: 1850

Re: For a 1994 16 SL: Add T-Top or Canvas Top

A bimini is the recommended approach.

Carver is a respected brand for Boston Whaler's.

Follow these instructions. Order the stainless steel option.

https://www.boatcoversdirect.com/products/bimini_tops/by_dimensions/
by Phil T
Fri Jul 28, 2023 12:58 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Cutting Unibond Hull in Half to Add Length
Replies: 5
Views: 2198

Re: Cutting Unibond Hull in Half to Add Length

You would need extensive fiberglassing experience.

The required effort would amount to hundreds of hours, thousands of dollars and a wrecked hull with limited to no resale value.

Get a 17' Super Sport instead.
by Phil T
Wed Jul 26, 2023 2:42 pm
Forum: SMALL BOAT ELECTRICAL
Topic: Perko Battery Swtich Needs replacing
Replies: 6
Views: 2110

Re: Perko Battery Swtich Needs replacing

George - Just replace with another 8501 or a Blue Seas 9001E or a BEP. PERKO 8501DP https://www.perko.com/catalog/battery_switches/148/medium_duty_battery_selector_switch/ BLUE SEA SYSTEMS 9001e https://www.bluesea.com/products/9001e/e-Series_Selector_Battery_Switch BEP 701S-B https://www.bepmarine....
by Phil T
Wed Jul 26, 2023 2:40 pm
Forum: The GAM
Topic: Assessing Hull with Unusual Cracking
Replies: 10
Views: 2397

Re: Assessing Hull with Unusual Cracking

Post some photos.
by Phil T
Wed Jul 26, 2023 2:36 pm
Forum: The GAM
Topic: Vendor for new Outboard Engines
Replies: 2
Views: 2001

Re: Vendor for new Outboard Engines

Unless it is less than 60hp, I do not know of anyone who has had a good experience with any "online" vendor. You need to look at a local dealers. If you list your general location and what brands you are considering, we may be able to suggest a shop or two. If you are trying to go cheap on...
by Phil T
Wed Jul 26, 2023 2:33 pm
Forum: The GAM
Topic: SPORT 15 Seating: OEM or Not
Replies: 2
Views: 1880

Re: Assessing 1977 15ft sport

Not that there is anything wrong with those.
by Phil T
Wed Jul 26, 2023 2:29 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2016 240 DAUNTLESS; Water Seeping from Screw Fastener Hole
Replies: 3
Views: 1964

Re: 2016 240 DAUNTLESS; Water Seeping from Screw Fastener Hole

Every screw into the boat should have sealant in the hole and under the head. Prior to installing the new pump, you want to remove as much water as practical. ⋅ Over-drill the holes by two bit sizes; ⋅ suck some of the surface water out using a shop vacuum on each hole; note resu...
by Phil T
Thu Jul 20, 2023 10:47 am
Forum: REPAIRS and MODIFICATIONS
Topic: ULTRA MARINE or FLOUNDER POUNDER as Vendor
Replies: 5
Views: 2075

Re: ULTRA MARINE or FLOUNDER POUNDER as Vendor

Ultra Marine and Flounder Pounder have a solid reputation and many Whaler owners sing their praises. Flounder Pounder offers OEM parts that are overstock so you know the items provenance. Ultra Panel is a bit on the expensive side and many owners have turned to less expensive options for dash panels...
by Phil T
Mon Jul 17, 2023 2:23 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Length of fill hose and vent hose for 2007 Dauntless 180
Replies: 4
Views: 2068

Re: Length of fill hose and vent hose for 2007 Dauntless 180

It is not published.

You need to pull the hose to get the exact length or overestimate. Run a garden hose over the deck to simulate path.
by Phil T
Mon Jul 17, 2023 12:47 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2003 Nantucket 190 Livewell Drain Repair
Replies: 7
Views: 2150

Re: 2003 Nantucket 190 Livewell Drain Repair

Highlighted section: ..an expedient repair to the container by using a stainless steel drain fitting with about 4-5" flange and 1.5" elbow and hose barb. These are available through many plumbing supply stores. This drain is sealed with 3M 5200 or equivalent and performs quite well. Aside:...
by Phil T
Sat Jul 15, 2023 6:54 pm
Forum: The GAM
Topic: How to Siphon Gasoline from Fuel Tank
Replies: 4
Views: 1995

Re: How to Siphon Gasoline from Fuel Tank

If the fuel with treated a stabilizer product when it was new, it should be good for at least 16 months in my experience. The E-TEC has a formed fuel line in the engine that runs approximately one-foot forward of the engine where it is joined to the boat's fuel line using a hose barb and either Oeti...
by Phil T
Sat Jul 15, 2023 6:37 pm
Forum: PERFORMANCE
Topic: 1985 OUTRAGE 18 120-HP
Replies: 2
Views: 1857

Re: 1985 OUTRAGE 18 120-HP

I am unable to find the gear ratio for that model of engine. Based on reviewing other engines with that hull, I think a 13x19 or 20" BPR Viper or a Powertech SCD 13x19 would be a good start. For the tough prop selection cases I deal, I consult with a few specialty prop shops who know Whaler hul...
by Phil T
Fri Jul 14, 2023 4:39 pm
Forum: The GAM
Topic: 1964 NAUSET Insurance Value for Total Loss
Replies: 10
Views: 2338

Re: 1964 NAUSET Insurance Value for Total Loss

The value of a rehabbed NAUSET with quality brightwork and gel coat finish, with a modern FOUR-stroke-power-cycle engine, a roadworthy trailer, basic equipment, and gear is way north of $20,000. Check the [asking price on a STRIPER 15 in an advertisement] seen below. Restored_15_Sport_Read_Fasse.jpg
by Phil T
Fri Jul 14, 2023 4:32 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2003 Nantucket 190 Livewell Drain Repair
Replies: 7
Views: 2150

Re: 2003 Nantucket 190 Livewell Drain Repair

Use JB Weld for Fiberglass/Plastic.
by Phil T
Fri Jul 14, 2023 10:26 am
Forum: The GAM
Topic: 1964 NAUSET Insurance Value for Total Loss
Replies: 10
Views: 2338

Re: Valuating a Classic Whaler

Most insurance company values on Whalers are typically low with no connection to market value. If you post/email photos that show the boat, we can give you a better number. If the company is under valuing the boat, you should purchase a policy with a declared value. I did a bow-to-stern overhaul on ...
by Phil T
Fri Jul 14, 2023 10:21 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1986 MONTAUK 17 Wood Locations
Replies: 5
Views: 2102

Re: 1986 MONTAUK 17 Wood Locations

It is customary to use the stern eye and the bow norman pin for securing lines.

If you need a midship spring line, you can use one of the vertical rail stanchions.
by Phil T
Fri Jul 14, 2023 10:16 am
Forum: MARKETPLACE
Topic: Appraisal: 1976 17-footer
Replies: 3
Views: 2018

Re: Appraisal: 1976 17-footer

The 17-footer being appraised is NOT a Newport as it is missing the cap and bow deck. A 17-footer with a non-OEM interior would be referred to as a 17-Custom. While you have invested about $15,000 in the boat, its market value is about that. Add the adjustment for location in California and the appr...
by Phil T
Thu Jul 13, 2023 2:10 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Engine Water Pressure Drops with Engine Speed Increase
Replies: 16
Views: 8444

Re: Engine Water Pressure Drops with Engine Speed Increase

Q3: have you checked that the gauge is operating correctly?
by Phil T
Tue Jul 11, 2023 7:21 pm
Forum: REPAIRS and MODIFICATIONS
Topic: My Recent Experience with Replacing Keel Rollers
Replies: 2
Views: 1806

Re: Recent Prices for Keel Rollers

I agree, prices are stupid.

Consider installing a roller on each side of each cross member.

I went with stainless shafts drilled for cotter pins and non-marring rollers. See

https://www.sturdybuiltonline.com/12-inch-Yellow-Poly-Vinyl-Boat-Trailer-Keel-Roller_p_2400.html rollers.