CONTINUOUSWAVE

Phil T

Most insurance company values on Whalers are typically low with no connection to market value. If you post/email photos that show the boat, we can give you a better number. If the company is under valuing the boat, you should purchase a policy with a declared value. I did a bow-to-stern overhaul on ...

Phil T

It is customary to use the stern eye and the bow norman pin for securing lines.

If you need a midship spring line, you can use one of the vertical rail stanchions.

Phil T

The 17-footer being appraised is NOT a Newport as it is missing the cap and bow deck. A 17-footer with a non-OEM interior would be referred to as a 17-Custom. While you have invested about $15,000 in the boat, its market value is about that. Add the adjustment for location in California and the appr...

Phil T

Q3: have you checked that the gauge is operating correctly?

Phil T

I agree, prices are stupid.

Consider installing a roller on each side of each cross member.

I went with stainless shafts drilled for cotter pins and non-marring rollers. See

https://www.sturdybuiltonline.com/12-inch-Yellow-Poly-Vinyl-Boat-Trailer-Keel-Roller_p_2400.html rollers.

Phil T

I would NOT [remove the cap on a NEWPORT in order to attempt to create a MONTAUK].

The NEWTAUK boats are revered as an improvement to both [NEWPORT and MONTAUK] models. A few dealers offered the NEWTAUK for only a few years.

Some owners converted [NEWPORT models to be NEWTAUK hybrids].

Phil T

I recommend to all new owners to replace all the through hulls as a matter of better safe than sorry . Nauset Marine is a good parts source if you are east of the mid-atlantic states. Derek, Jason, Justin, Parts Department http://www.nausetmarine.com The Boat House is good if you are west of there. ...

Phil T

A2 - Carver makes really good canvas products that are custom fit or universal fit for Boston Whalers. One of their distributors, Boat Covers Direct has a good rep from owners. They have 6 versions for your model, depending on your options. Go to https://www.boatcoversdirect.com/products/bimini_tops...

Phil T

I highly recommend you download all the parts diagrams for your boat from the Boston Whaler website. These pdf drawings show what is installed and where as well as parts lists. Go to https://www.bostonwhaler.com/resources-and-maintenance.html Enter YEAR Enter MODEL FAMILY Enter MODEL Select Type - D...

Phil T

Even with moving the battery to the console, the hull will have a significant stern bias at rest and coming off plane may ship water over the transom. I recommend you add the necessary weight to the transom to simulate the proposed weight of the new engine, jack plate and power pole. Drive around, c...

Phil T

I think the courtesy dock designs being installed on lakes are quite poor from a boater's perspective. Using precast concrete sections (narrow and long) are easy to install and repair and are less prone to damage. Having exposed posts every 8' or whatever makes is hard to land a boat let alone walk ...

Phil T

Stay with the same brand and model of propeller but buy a new propeller with a pitch greater by 2-inches

Note: the engine speed maximum at full throttle is 6300-RPM

Phil T

You are looking at $5,000 to $10,000 in repairs at a shop who has experience with Boston Whaler construction.

If you add your location, we might be able to give you recommendations.

Phil T

You will have a long search.

With the passing of time, the number of vintage Whalers in the 18 to 22-foot range has fallen and prices have increased.

A classic Outrage 22 in decent condition with a post-2000 engine in the Gulf region fetch close to $40,000.

Phil T

What was your prior username 15 years ago?

Phil T

At one point Sue Lodel, Parts Manager at The Boat Shop, formerly Beacon/Twin Cities Marine, had some in stock. Give her a call and check - ‭(920) 793-2715‬. The new company website is horrible. If they are not available, consider six squares of Dri-Dek. Almond for Desert Tan hulls, white for post cl...

Phil T

Boston Whaler Customer Support has been centralized and scaled way way back. They are referring owners of models no longer in production to the owner sites on the internet.

Phil T

Daleshank wrote:Q3: will a 13-1/8 x 18 TALON suffice?

Yes.

Also the TURBO 1 is similar in the same size as the Performance Series TALON.

Shop the web. Prices vary.

Phil T

Turned out as I hoped it would.

Well done for saving her.

Phil T

Add a gasket on the lip underneath.

Phil T

I would not replace the wood, as there is every chance the wood can be restored with a little elbow grease. I would not purchase any imitation parts from Specialty Marine as they are lower quality and overpriced. Bob Latourelle is known to Boston Whaler owners for high quality wood interiors and par...

Phil T

If you want a remote consultation, send me a PM.

One of the best restoration shops is FasseCo. They are near Nashville, Tennessee.

Read Fasse is the Principle and Owner.

Not for the faint at heart.

https://fasseco.com/

Phil T

The technical term for the hardware you are refering to is "backing plate".

: Bow Rail Backing Plate - Nauset Marine; Bow_Rail_Backing_Plate.jpg (30.97 KiB) Viewed 1837 times

They are available from Nauset Marine.

https://www.nausetmarine.com/boston-whaler-parts/hardware/rail-hardware/1067206-backing-plate/

Phil T

There is no factory propeller The selling dealer sold a propeller that they or the buyer selected. Many owners have repowered their Montauk with an F70. (Wide open throttle is 6300). Their testing resulted in these recommendations:* 13 x 17 Yamaha Painted SS 13.25 x 14 Yamaha Performance Series 13-1...

Phil T

When relocated the battery on my 1987 Montauk 17, I ran AWG-2 marine battery wire from the engine to the console and a new OFF-ON battery switch. I recall it was about15 or 17 feet of wire. To do it again, I would go with 4-AWG wire. Use of 2-AWG wire was excessive. Cut the floor and have the batter...

Phil T

Q1: What is the best method to restore chalky Z legs? I have enough paint to paint the Z-legs

Sand with fine grit, wipe with acetone. Apply several thin coats of a Krylon paint for plastic.

Q2: will Penetrol restore chalky Z-legs

For a season, reapplication each year is needed.

Phil T

If the above does not work, replace the zirk fitting in the tube.

Phil T

Use brass stud catches:

https://shop.hamiltonmarine.com/products/stud-catch-brass-2-5-16--29618.html

Phil T

Seal the walls of the hole with epoxy and add a deck grommet to cover the hole with a small cutout for the fuel line.

Phil T

METHOD TO RAISE ENGINE MOUNTING HEIGHT FOR HOME USE Raising the [engine mounting height] us a do-it-yourself operation IF: ⋅ the engine mounting lower bolts are in the slots; ⋅ the boat is on a trailer; and ⋅ you can have someone help you at one stage. A second set of...

Phil T

You want the engine installed so the anti-ventilation plate is 1-1/2 to 2-inches above the bottom of the boat. Another way of expressing this: assuming the top engine bolt hole is 1-7/8 below the top of the transom, mount the engine two-holes-up; this will put the top bolt in the third hole counting...

Phil T

Yes, many feel that the 2010 150 Supersport is underpowered with a 40-HP engine. You will not recoup your investment if you repower and sell in one to four years. Keep the boat as is, then sell it, and buy a different boat that suits your needs. The traditional marketplace principles for boats has r...

Phil T

From Attwood, a manufacturer of this type of product: The integrated fuel demand valve, used in conjunction with integrated fuel systems, is for below deck use, eliminates pressurized fuel from reaching fuel distribution lines and your engine and ensures that fuel is provided to the engine on demand...

Phil T

I would contact one of these Boston Whaler dealers known for superior customer service and authentic parts.

The Boat House, former Beacon Marine/Twin Cities
Sue Lodel, Parts Manager
‭(920) 793-2715‬

Nauset Marine
Derek, Jason, Justin - Parts Department
‭(508) 255-0777‬

Phil T

[The fuel system seen in Figure 2 above] is terrible setup. The gray hose is not alcohol-resistant and is prone to degrade and contaminate the carburetors and fuel injectors. Replace any fuel hose that does not have alcohol-resistant printed on the outside. With a traditional manual vented cap or th...

Phil T

First off, there is moisture in the hull. It is expected in a hull that old. The question is how much and if is something that needs to be addressed. With every Whaler, I first look at how the boat sits in the water with a full fuel load and no passengers. Where is the water line on the outside of t...

Phil T

I think 3/4-inch plywood will suffice.

Several coats of epoxy by brush will seal it. Take time for the edges.

Phil T

Most of the PVC is not structural.

The achilles heal of the seat was the plywood was not sealed.

If you used plywood, cut to size and then coat with epoxy. It will outlive you.

Phil T

I googled tilt helm boot. Skimmed the results. One result is one of my favorite suppliers, Wholesale Marine. Did a search on their site for tilt steering and there it was.

While it only took me 30 seconds, I am constantly searching for Whaler parts on a weekly basis.

Phil T

Is this it?

https://www.wholesalemarine.com/seastar ... elms-6-pk/

Phil T

Keep up the good work.

Phil T

Jim - The phrase "standard propeller" is outdated, inaccurate and not always helpful. If anything, it fosters the continuation of the past sterotyped information. Propellers are not included by the manufacturer and are sold separately from outboards larger than 30hp. The F70 has a WOT limi...

Phil T

Many older generation outboard engine installers and those not well versed with Boston Whalers install the engines too low due to lack of knowledge or sheer laziness. "I do this all day sonny I know what I am doing," is frequently reported. Dozens and dozens of owners have tested new engin...

Phil T

There is a good chance the current version of the rails for the Montauk 190 (redesigned 2018) are different than the first generation. EDIT - After doing a comparison, the rear side rails on the pre and post 2018 are identical. Marine Liquidators in Ft. Pierce buys overstock, leftovers from Boston W...

Phil T

Classic 16' owners who have installed a Yamaha F90 have done extensive testing. These are their recommendations. Note- Engine is mounted 2 holes up, with the top bolt in the 3rd hole counting down from the top. 13-1/3 x 18 Yamaha Talon (Performance) 13 x 19 Yamaha Painted SS 13 x 19 Powertech SCD 13...

Phil T

Did you want me to work on getting the measurements from 190 owners?

Phil T

The entire 2023 build schedule was sold out months ago. With demand slowing, there may be some flexibility in 2024 but I would not have high hopes.

There is a chance they will have their quality control problems under control next year.

Phil T

Dave--you have missed a very important rigging requirement:
From my prior post:

Engine mounting: Engine is mounted two-holes-up with the top engine bolt in the 3rd hole, counting down from the top.

Always include the model name and size when referring to a propeller.

Phil T

Under the cover of the [remote throttle-and shift control] there is an adjustment knob or screw that creates resistance so the throttle handle does not slide back to neutral. If you provide us the make/model of shifter, we may be able to provide guidance on how to remove the shifter cover and gain a...

Phil T

It reads as though your dealer has been very responsive to correct factory problems. Given the stories of problems with dealers, I think it important to include the dealer's name as a favorable dealer story on how efforts to correct defects should be handled. If you do pursue a buyback I would not e...

Search found 2607 matches