CONTINUOUSWAVE

Phil T

Was the engine installed by a dealer or did you do it yourself? I would ask the dealer to borrow a different prop. Something is very wrong. A Yamaha dealer should have a Yamaha prop available. Look at the list I posted. You should be able to hit 40 mph easy. For the time being, remove the tabs to el...

Phil T

I don't recall Hamilton Marine carries the Steersman brand. I go thru manufacturer's website. https://steersman.com/html/buy.html SeaChoice offers a version: https://www.amazon.com/SEACHOICE-SeaStar-Solutions-Stainless-Steering/dp/B0006ZCHJQ/ref=sr_1_2?dchild=1&keywords=SEACHOICE+STEERING+GUARD&...

Phil T

Given the reports of the limitations of the "sea trial", I would suggest the prospective buyer ask the selling dealer to provide one or two 270 Vantage owners to talk to. They may even offer a ride to show off their boat.

Phil T

Have you completed the required 10 hour break-in procedure as detailed in the manual? If not, complete the procedure and then check performance. Please go back and re-read my post. Prop size/performance is NOT universal across brand/model. A Turning Point aluminum x by 17 will not run the same as a ...

Phil T

The 1990-1995 Outrage 17I is self bailing with one major condition. With the stern sump plug removed significant volumes of water will enter to reach equilibrium with the outside water level. Once reached, no additional water will enter. I ran my 1991 Outrage 17I with the sump drain plug inserted an...

Phil T

Check tool rental stores. Possible to find a higher quality tool for same/less money.

Phil T

Depending on your location in the US, that is a reasonable price. I would expect prices in CA to be higher, Florida lower. A smaller tank will not save you significant money. Is the existing tank plastic? If so, there is no replacement available. Each model has a unique shape that was custom. A cust...

Phil T

If you really want self-bail, consider ball type scuppers.

Many owners with different models, but the same concern, say it really helped.

Phil T

Once we work through the waterline concern, we really should discuss your engine rigging/prop selection and boat performance.

The engine is mounted significantly lower than it should be.

Phil T

My advice is to insert the drain plugs on the inside of all of the deck and splashwell drains and relaunch the boat. Measure the waterline in relation to the Whaler logo. While this model has the same hull design as the "classic" Outrage 18, it is 500 lbs heavier due to the additon of the ...

Phil T

Here are a few photos of other Outrage 19's showing stern position.

Note the waterline in relation to the Boston Whaler logo.

Phil T

A waterline above the transom drains is not unheard of. I would install ball type scupper covers. One of several brands - https://www.boatoutfitters.com/flow-max-ball-scupper-clear?msclkid=733f78c999da132dc31127fe74ab5492&utm_source=bing&utm_medium=cpc&utm_campaign=TNT_Shopping%20-%20Des...

Phil T

Engine height and prop selection is not about top speed necessarily. It is about rigging the motor so the engine runs the most efficient and peforms well at all speeds. An analogy is riding a ten speed bike. You want to select a gear that allows you to go at a good speed, with low effort on the flat...

Phil T

While I do not have a specific boat model/engine prop recommendation for the Dauntless 15/F70, I will use similar models to provide some guidance. Owners who have the F70 on the classic 15 Sport recommend: 13 x 16 PowerTech SCD 13.25” x 17 PowerTech SCD3 13-1/4” x 17” Turbo 1 Owners with an F70 and ...

Phil T

Thanks to the many corporate owners of Boston Whaler over the years, there are several "versions" of the Outrage 19, hence the question and the confusion. As shown in the reference article, http://continuouswave.com/whaler/reference/specifications.html there is the: Outrage 19 (also referr...

Phil T

After looking at the parent thread, I see now the lower holes will need to be filled with hardwood plugs. Do not use a dowel since the wood grain will be in the incorrect orientation and future shrinkage will crack any gelcoat/epoxy repair. To drill holes that break the surface of the splashwell, th...

Phil T

aluminum three-blade propeller 13.2 x 19-pitch After spending $8500-9,000 for an engine, the dealer slapped on a $140 prop. It's similar to buying a Lexus SUV and installing tires from a Big Wheel. Owner recommendations for the 16'7 hull with a E-Tec 90hp include: 13.5 x 20” Raker 13-7/8" x 19...

Phil T

To add location:

Click on your name shown on the right of your post
To the right of your UserName, click "edit profile"
Enter location information
Select "Submit" button below.

Phil T

Please clarify - My engine is rated for 5280 rpms. (on sticker) What "Sticker" and where is it? Can you share a photo? Which of the following is what you see: Top of engine bracket holes 0 - "all the way down 0 - bolt here is "1 holes up" 0 - bolt here is "2 holes up&qu...

Phil T

There are only a dozen or so tank dimensions that are documented so the majority of owners replacing a tank have two choices.

Order from FMT, a good option if you live within 500 miles of Henderson, SC

-or-

Remove the tank and provide it to the local fabricator to use as a template.

Phil T

While you repair the rail, you can pull a tube using the stern eyes on the outside of the transom. They are more than strong enough.

If you add your general location to your profile, one could provide local vendors to repair, replace your rail.

Phil T

I think it may be only running on 1 or 2 cylinders.

Take the boat out and shoot a video of the engine idling, planing off and runnning wide open. Post a link or email to me and I will post it for you.

Phil T

Boston Whaler has not in the past or present ever released sales volume for any model. Given the Temptation series 2000, 2200 and 2500 were only in production for the 1987, 1988, and 1988 model years, the number built is relatively small. I would estimate less than 70 of all models were produced. Wh...

Phil T

Trailers are regional. Shop brands in your area. Shop dealers hard, prices vary WIDELY for the same model. Galvanized trailers will give you a shorter total length with boat loaded. LoadRite has 2 decent choices (aluminum or galvanized) and a decent dealer network in NJ. Galvanized model - http://ww...

Phil T

The OP is referring to a resettable breaker.

A fuse is not repairable or resettable.

Phil T

I recall a prior conversation regarding Mercury and Smartcraft error messages.

http://continuouswave.com/ubb/Forum6/HTML/002394.html

Mercury does not include a list of the codes and descriptions of potential messages. One must visit a dealer.

Phil T

The adage "aluminum props are better" is outdated and now false due to the introduction of shock absorbing hubs. Stainless props deliver better performance, efficiency and are less prone to damage. Dealers/yard guys say aluminum because they are cheap, cheaper for them to stock and will le...

Phil T

bolts in the 4th hole counting down from the top.

When done, there will be 3 empty holes above the bolt.

Phil T

Having seen and read of the choppy conditions that occur on Galveston and Casco Bays, I would proffer a different choice. While a Montauk 17 is good for calm day, it is a bit uncomfortable in short chop. I would suggest a model with more of a V: 1990-1995 Outrage 17 or 1996-1999 Outrage 17 II 1981-1...

Phil T

Remind us.

Is the boat in Maine or Texas?

Phil T

You definately want to move up two-inches in pitch with the same make and model of propeller . If you change propeller models the pitch sizes are not applicable. To control bow rise, the one feature that will help is smart tabs. Read "Thegage"'s post, 2nd to last on this thread: http://con...

Phil T

Nick - IDK.

If the OP has a Bigfoot model, the prop calculator returns 16" of pitch.

Phil T

That is the stern platform from a 1972-1976 Bass model.

Phil T

A 2004 any make/model is not "almost new". With the prop modifications, we have no idea what the pitch of the current prop. Prior to 2002 the selling dealer rigged the engine and selected the prop. It is clear that the current prop has too much pitch for the hull. Note that Trophy Plus pro...

Phil T

As of a few years ago most outboard engines moved away from analog gauges. Some engines are rigged [with electronic shift and throttle (EST) remote controls]. My point: any money saved by recycling rigging has been diminished. Many engines support engine data being displayed on GPS/Chartplotter/Moni...

Phil T

To "fix" this, the entire area of new "paint" or "gelcoat" (not the same. see below) is not a DIY. Gelcoat and paint are completely different materials. If the repaired area is paint, it will need to be completely removed and matched gelcoat will need to be sprayed. To ...

Phil T

Bah, that is nothing to concern yourself with. Easy DIY repair. The boat is 16 years old. I would expect to find dents, scratches, scrapes, dings, gouges. If there weren't any I would be concerned. Be more concerned with drain tubes, keel rash, loose fittings, wiring in console and engine service hi...

Phil T

Go larger.

You will be very crowded.

Think 16'7/17' models.

Phil T

There is no information on Boston Whaler's website to determine if the spaces inside the rear quarter seat/platforms contain structural foam or are hollow. Prior to any investigation, I would submit a detailed query to the factory Customer Service team to ascertain the answer. https://www.bostonwhal...

Phil T

How can you expect any decent information when we have no idea what year and model you have?

There is more than one Super Sport.

Details.

Photos would also help.

Phil T

Andy - Welcome to CW. It is worth noting that Moeller produces several models of above deck fuel tank that are similar, but different. Prices are also different. Moeller 24 gallon above deck tank - #031624 (not low perm) Size: 29.25" L x 19.00" W x 12.25" H Color: RED Price: ~ $296 ht...

Phil T

Consider making a replacement out of KING StarBoard.

Phil T

Mike Homewood and Archie Cassidy did conversions.

Phil T

While Great Lakes was/is the OEM supplier for canvas, Mills makes a good product, as do others. Fasteners in the hull are acceptable, just add a dab of sealant , not adhesive in the hole and under the head of the screw. If the screw head will touch the gelcoat, the top of the hole should be chamfere...

Phil T

Please detail what "stalls" means. RPM falls, drops, shuts off, stutters, shakes? At what points? Can you make it happen? If so what do you do to reproduce.

How many hours on the engine.

I would take it back to the dealer and have them assess. They were the last to touch the boat.

Phil T

You said " The engine was broken in over six hours." The manufacturer recommendation is a 10 hour break-in period. Were the specific operating guidelines for hours 0-2, 3 and 7-10 followed? Has WOT rpm ever been momentarily at 5800-6200? I would have the engine mounted at least 2 holes up ...

Phil T

The Outrage 19 II has a hull weight of 1900 lbs and a max hp of 150hp. It is the same hull design and max hp of the classic Outrage 18 but with the added liner and redesigned interior/console.

The DF140 has a WOT range of 5200-6200 rpms and a gear ratio of 2.59:1

Phil T

Please do NOT post the same query in multiple forums.

Your post in Repairs and Modifications has been deleted.

Phil T

Xavier— Is the DF140A engine still in the break-in period of zero to ten hours? At what altitude are you boating? What is the mounting height of the engine? How far above the lowest possible mounting is the engine now installed? Measure in units of 0.75-inch or “holes” from lowest possible position.

Phil T

Sorry Bill, another recommendation to find a different candidate. There have been a handful of conversions of cabin or cuddy models to a center console. They were not pretty to see or easy to do. Most owners admitted the work required was far more than expected. The lack of OEM hatch covers necessit...

Search found 2607 matches