Search found 2602 matches

by Phil T
Wed Oct 11, 2023 7:26 pm
Forum: The GAM
Topic: Wood locating diagram for a 2018 150 Super Sport
Replies: 3
Views: 1842

Re: Wood locating diagram for a 2018 150 Super Sport

Sorry for the date typo on my part. In section 5-10 of your owners manual is the reinforcement diagram. It shows item E, a 7" x 13" piece of phenolic on the port side corner of the transom as well as item A3, a 1-1/2" plywood area measuring 20" x 42". Here is a link to the O...
by Phil T
Wed Oct 11, 2023 7:15 pm
Forum: PERFORMANCE
Topic: 1996 17 Outrage II Re-power
Replies: 19
Views: 4161

Re: 1996 17 Outrage II Re-power

Michael - F150 for sure. Make sure engine is mounted so the top bolt is in the 3rd hole counting down from the top. As for props here are a few suggestions. All stainless, no aluminum. Yamaha Performance 14.25" X 18 Reliance 14 1/4 x 17 Mercury Enertia 14x18 For pulling skiers you will want a 4...
by Phil T
Tue Oct 10, 2023 6:32 pm
Forum: PERFORMANCE
Topic: 1996 17 Outrage II Re-power
Replies: 19
Views: 4161

Re: 1996 17 Outrage II Re-power

Michael--the [Yamaha F150 engine] will not be a problem for the hull. Depending on how you use your boat, the number of persons aboard, the weight of gear, the Yamaha F130 would work, too. If you go far from the coasts, carry a large load and need the power in a pinch, stay with the 150-HP engine. T...
by Phil T
Sat Oct 07, 2023 9:03 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2007 190 Outrage: Cost to Install Electric Trolling Motor
Replies: 9
Views: 2201

Re: 2007 190 Outrage: Cost to Install Electric Trolling Motor

You will not find one.

It is for this reason owners fabricate an "extention cord".
by Phil T
Fri Oct 06, 2023 9:35 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2007 190 Outrage: Cost to Install Electric Trolling Motor
Replies: 9
Views: 2201

Re: 2007 190 Outrage: Cost to Install Electric Trolling Motor

Owners have installed a trolling motor on a boat that does not have a [factory installed pre-wired electrical receptacle at the bow to provide power]. To do this without major modifications, batteries are installed in the center console. The center console floor is cut and the batteries sit on the d...
by Phil T
Fri Oct 06, 2023 7:14 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2007 190 Outrage: Cost to Install Electric Trolling Motor
Replies: 9
Views: 2201

Re: 2007 190 Outrage: Cost to Install Electric Trolling Motor

That is a horrible estimate. Knuckleheads.

It is $400-$600 in materials to rig up an extension cord and an outlet on the console and add a hinged section to the rail.

I have specifics if you want.
by Phil T
Fri Oct 06, 2023 6:53 pm
Forum: The GAM
Topic: 2012 130 Super Sport Trailer in Naples, Florida Area
Replies: 10
Views: 4138

Re: 2012 130 Super Sport Trailer in Naples, Florida Area

The Karavan trailer that comes standard with the small Whaler models is the economy model. They don't hold up very well.

I would prefer to look at Rocket or Load Rite brands.
by Phil T
Fri Oct 06, 2023 6:50 pm
Forum: The GAM
Topic: Wood locating diagram for a 2018 150 Super Sport
Replies: 3
Views: 1842

Re: Wood locating diagram for a 2018 150 Super Sport

If you scroll down to the swim mounting diagram here - https://www.nausetmarine.com/wp/wp-content/uploads/nausetmarine.com/2021/09/2003-2008-150-SPORT.pdf - you will see where to mount the platform. Note the bottom screws are lags. As for Ray's platform, consult with him. I recall that his design al...
by Phil T
Thu Oct 05, 2023 10:09 am
Forum: The GAM
Topic: 2013 130 Super Sport Self-bailing
Replies: 15
Views: 17215

Re: 2013 130 Super Sport Self-bailing

Dave -

I don't completely disagree with your comments as I too had similar experiences.

Somewhere the world got confused on the word self bailing and self draining

Many owners new to Whalers expect the boat to be totally dry when you pull the plug.
by Phil T
Tue Oct 03, 2023 6:17 pm
Forum: The GAM
Topic: Six Question on Worth of a 2001 VENTURA 16
Replies: 2
Views: 1776

Re: 2001 16' Ventura

Without seeing photos, pricing will be very general. [A 2001 VENTURA 16] without an engine or with an older engine that may not run well [may sell for] $6,000 to $7,000 The costs to buy and install a new engine: ⋅ a new 90-HP engine will cost $11,000 to $13,000 installed; ⋅ a new...
by Phil T
Mon Oct 02, 2023 10:16 am
Forum: REPAIRS and MODIFICATIONS
Topic: Dauntless 15/16 center console railing removal for clearance
Replies: 1
Views: 1615

Re: Dauntless 15/16 center console railing removal for clearance

look at the feasibility of hinging the console so you don't need to sacrifice the windscreen/rail.

How much clearance is there at high water?

If it really is tight, the 15' Sport or 17 Standard or Super Sport is going to be your only option.
by Phil T
Thu Sep 28, 2023 2:02 pm
Forum: REPAIRS and MODIFICATIONS
Topic: When to Replace Fuel Tank
Replies: 7
Views: 3712

Re: When to Replace Fuel Tank

Expect to pay $3,000 to $5,000 for a boat yard to replace the fuel tank.

If it ain't broke, why fix it?
by Phil T
Wed Sep 27, 2023 9:40 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Repair Rivet Fastener Holes in 1997 MONTAUK Rub Railing
Replies: 9
Views: 2329

Re: Repair Rivet Fastener Holes in 1997 MONTAUK Rub Railing

The Robertson fastener is commonly referred to as the square bit screw by the trade guys in the States.

Their use is very common in residential construction.
by Phil T
Wed Sep 27, 2023 9:33 pm
Forum: The GAM
Topic: Boat for Long Island Sound: c.2002 230 OUTRAGE
Replies: 25
Views: 3523

Re: Boat for Long Island Sound: c.2002 230 OUTRAGE

John and the crew at York Harbor Marine are great. They hosted a group of us during one of my gatherings back in the day. In addition to lunch and Whaler swag, they allowed sea trials of several models, including the just introduced Montauk 150. As you noted, the sea state outside the harbor can be ...
by Phil T
Mon Sep 25, 2023 11:25 am
Forum: The GAM
Topic: 1999 VENTURA 20 v. 210 VENTURA
Replies: 4
Views: 1855

Re: 1999 VENTURA 20 v. 210 VENTURA

The Ventura 210 is heavy and solid with an empty weight of 3300 lbs. This is 1,000 lbs over the Dauntless 20. A Ventura 210 owner, BlueWaterPirate, posted dozens of threads detailing his 4,000 hrs of use off the coast of the Carolina's. It was reading these over the years and a day spent on one off ...
by Phil T
Sun Sep 24, 2023 10:43 am
Forum: The GAM
Topic: 1999 VENTURA 20 v. 210 VENTURA
Replies: 4
Views: 1855

Re: 99 Ventura 20 vs. Ventura 210

The Ventura 20 was originally the Dauntless 20.

The Ventura 210 is a different model completely. It is a beast and a tank.

If I had my choice, Ventura 210 hands down.
by Phil T
Sun Sep 24, 2023 10:39 am
Forum: REPAIRS and MODIFICATIONS
Topic: 1986 Outrage 18 Tar-like Goop Seeping from Gel Coat Crack
Replies: 5
Views: 1901

Re: 1986 Outrage 18 Tar-like Goop Seeping from Gel Coat Crack

[The black tar-like goop is] uncured resin.

Test [the fuel tank to a maximum pressure of] 2-PSI.

ASIDE: I hope you got by okay with that storm. I talked to Chris Leblanc (TBS,The Boat Shop) south of Halifax and it was rippen' there.
by Phil T
Sun Sep 24, 2023 10:38 am
Forum: REPAIRS and MODIFICATIONS
Topic: Repair Rivet Fastener Holes in 1997 MONTAUK Rub Railing
Replies: 9
Views: 2329

Re: Best way to repair enlarged rivet holes - 1996 Montauk rubrail

The recommended approach is to fill the old holes and drill new holes for the rivets, not to reuse the same holes.
by Phil T
Fri Sep 22, 2023 8:23 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2017 170 MONTAUK Unusual Transom Saver
Replies: 2
Views: 1665

Re: 2017 170 MONTAUK Unusual Transom Saver

I would not use that as it is exacerbating the possibility of striking the ground at a curb cut or grade change.

A 2x4 block of wood between the bracket and the outboard has worked for me for 20 years.
by Phil T
Fri Sep 22, 2023 8:21 pm
Forum: SMALL BOAT ELECTRICAL
Topic: Four Question on Boat Electrical Problems
Replies: 10
Views: 2199

Re: Four Question on Boat Electrical Problems

I have never heard of this type of frequent failure of a new Rule pump.

The pump is not being installed properly.

The wiring must be done properly and the splicing must include watertight connections such as heat shrink butt connectors.

See the instructions with the pump.
by Phil T
Fri Sep 22, 2023 8:14 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Replace Mechanical Fuel Gauge with Electrical Remote Gauge
Replies: 5
Views: 1851

Re: Replace Mechanical Fuel Gauge with Electrical Remote Gauge

http://www.e-components.net has the OEM fuel tank sender and [visual dial-pointer tank level gauges].
by Phil T
Fri Sep 22, 2023 8:12 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Replace Mercury 30-HP Remote Throttle-Shift Control
Replies: 7
Views: 2062

Re: Replace Mercury 30-HP Remote Throttle-Shift Control

I am not a fan of the large loops for the cables.
by Phil T
Thu Sep 21, 2023 5:58 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Replace Mercury 30-HP Remote Throttle-Shift Control
Replies: 7
Views: 2062

Re: Replace Mercury 30-HP Remote Throttle-Shift Control

Butch - Forgot you need a side mount. Consider: Yamaha 703...... https://www.simyamaha.com/premium-side-mount-control-703-48207-24-00/ Teleflex CH 1700 ... https://www.wholesalemarine.com/teleflex-ch1700-series-side-mount-control/?msclkid=fefe431e8acf1fbf50eb2612312117c6
by Phil T
Thu Sep 21, 2023 1:27 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Replace Mercury 30-HP Remote Throttle-Shift Control
Replies: 7
Views: 2062

Re: Replace Mercury 30-HP Remote Throttle-Shift Control

I have always wanted a classic Morse control with the red ball--the authentic one, not the cheaper imitations.

They shift so smoothly and neutral is really there--no vagueness.

Teleflex Xtreme cables get high praise from owners of Boston Whaler boats.
by Phil T
Tue Sep 19, 2023 7:01 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 2001 Dauntless 160 Washdown Pump
Replies: 3
Views: 1822

Re: 2001 Dauntless 160 Washdown Pump

I advise all Whaler owners to avoid at all costs cutting another drain or hole in the hull, especially below the waterline.

A bucket works.
by Phil T
Tue Sep 19, 2023 6:58 pm
Forum: The GAM
Topic: 13-footer: Use of Jet Drive Outboard
Replies: 1
Views: 1675

Re: 13-footer: Use of Jet Drive Outboard

You loose a fair amount of speed due to the inefficiency of the jet. You may need a 50hp or more to get the same speed as a 40hp.
by Phil T
Tue Sep 19, 2023 8:40 am
Forum: REPAIRS and MODIFICATIONS
Topic: 2008 Montauk 190 Moisture From Rub Rail Damage
Replies: 1
Views: 1620

Re: 2008 Montauk 190 moisture from rub rail damage

...to understand how much moisture [the hull] could possibly have--if any. Why do you think you have any moisture, or enough to concern yourself to entertain scales and weighing the boat? Where is the static water line on the exterior transom when the boat is at rest in relation to the splashwell? ...
by Phil T
Sun Sep 17, 2023 10:50 am
Forum: The GAM
Topic: 1982 Outrage 18 Waterline at Static Trim
Replies: 23
Views: 3028

Re: 1982 Outrage 18 Waterline at Static Trim

Go use your fabulous boat and stop wasting our time.
by Phil T
Wed Sep 13, 2023 8:52 pm
Forum: PERFORMANCE
Topic: 1982 OUTRAGE with HONDA BF150
Replies: 14
Views: 2679

Re: 1982 OUTRAGE with HONDA BF150

We don't even know what propeller you have now. Q17: Have you tried any of the recommended props I listed? You mention trying a four-bladed propeller without the model name or size, so we have no way to evaluate it as to it being a good propeller for that boat-engine combination. You need to underst...
by Phil T
Tue Sep 12, 2023 7:11 pm
Forum: The GAM
Topic: 1982 Outrage 18 Waterline at Static Trim
Replies: 23
Views: 3028

Re: 1982 Outrage 18 Waterline at Static Trim

Your deduction of a water problem is based on faulty assumptions. Many Outrage 18's have a sheet of foam sitting on the top of the tank from the factory. Moisture in the cavity sits on top of the sheet and clouds the inspection cover/fuel gauge clear cover. Many owners, during their inspection of th...
by Phil T
Wed Sep 06, 2023 8:42 pm
Forum: The GAM
Topic: 1982 Outrage 18 Waterline at Static Trim
Replies: 23
Views: 3028

Re: 1982 Outrage 18 Waterline at Static Trim

Let's turn this around 180 degrees.

Where is the waterline on your boat? Add some photos.

Why is this a concern?
by Phil T
Wed Sep 06, 2023 8:16 am
Forum: PERFORMANCE
Topic: NAUSET 16 Yamaha 90-HP
Replies: 4
Views: 1864

Re: NAUSET 16 Yamaha 90-HP

After reading your post and a good night sleep, I think you should upgrade the propeller to the Yamaha painted stainless steel model in 13 x 17. It will not need to be replaced if you hit a buoy or debris. The boat will perform better at all speeds. Just be happy you don't need an Enertia propeller ...
by Phil T
Fri Sep 01, 2023 10:36 am
Forum: REPAIRS and MODIFICATIONS
Topic: Re: 2000 Outrage 18 Fuel Tank Removal and Cleaning of Fuel Tank Cavity
Replies: 5
Views: 2261

Re: 2000 Outrage 18 Fuel Tank Removal and Cleaning of Fuel Tank Cavity

The first model I recall with plastic tanks was the V-22 Revenge in 1979. I did some initial research on tank alternatives for an owner sometime in the 2010's.
by Phil T
Wed Aug 30, 2023 7:26 pm
Forum: PERFORMANCE
Topic: Seakeeper RIDE
Replies: 1
Views: 1908

Seakeeper RIDE

Seakeeper has introduced their version of transom mounted control surfaces [that they call the Seakeeper RIDE]. For boats under 26-feet the retail price [of the appropriate Seakeeper RIDE device is] $4,500. For details visit: https://ride.seakeeper.com/how-it-works/ A Montauk 190 owner has just had ...
by Phil T
Tue Aug 29, 2023 7:47 pm
Forum: The GAM
Topic: Identify Model From Picture; Appraise Boat From Picture
Replies: 5
Views: 2298

Re: Identify Model From Picture; Appraise Boat From Picture

I think Fig. 1 and Fig 3. are the same.
by Phil T
Tue Aug 29, 2023 8:55 am
Forum: The GAM
Topic: 1999 160 DAUNTLESS: Information on Ski Pylon
Replies: 1
Views: 1847

Re: 1999 160 DAUNTLESS: Information on Ski Pylon

Q1: what ski pylon should I purchase and install on a 1999 Dauntless 16? Finding [a SKI PYLON] in the US or UK will be hard. Most owners of the Dauntless looking for [a SKI PYLON] get a custom-made pole, or use a transom mounted ring like [the TURBO SWING SKI TOW BAR]. https://turboswing.com/xxl-tu...
by Phil T
Mon Aug 28, 2023 9:25 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1996 Montauk 17 Hatch Hinge Repair
Replies: 13
Views: 2800

Re: 1996 Montauk 17 Hatch Hinge Repair

These fasteners are also referred to as: sex bolts binding barrels and screws Added vendors of them include: McMaster- Carr https://www.mcmaster.com/products/sex-bolts/ Bolt Depot.com https://www.boltdepot.com/Browse.aspx?Units=US&Category=Sex_bolts_%26_Mating_screws&Subcategory=Sex_bolts&am...
by Phil T
Mon Aug 28, 2023 6:09 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Electrical Switch
Replies: 6
Views: 2341

Re: Electrical Switch

Here are two photos for comparison.

RyanVo_console.jpeg
Fig. 1. Original helm console panels, switches, ignition and throttle from a 1993 Outrage 17.
RyanVo_console.jpeg (57.15 KiB) Viewed 2115 times


1992Outrage17_New_panels_new_gauges.jpeg
Fig. 2. New KING StarBoard panels, BPR gauges, ignition switch, and a custom switch panel with select switches I designed and ordered from New Wire Marine.
1992Outrage17_New_panels_new_gauges.jpeg (51.62 KiB) Viewed 2115 times
by Phil T
Sat Aug 26, 2023 7:29 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Gasoline under floor: 2019 170
Replies: 6
Views: 2227

Re: Gasoline under floor: 2019 170

Inspect the fuel supply hose, the vent hose, and the fuel fill hose where they attach to the tank. Tighten the connections. If they used a crimped fitting, remove it and replace them all with a stainless hose clamps. Check the in-line fuel primer bulb. Inspect the fuel tank check valve or demand val...
by Phil T
Sat Aug 26, 2023 7:22 pm
Forum: MARKETPLACE
Topic: Re: Appraisal on 1977 Newport PICTURES
Replies: 3
Views: 2212

Re: Appraisal on 1977 Newport PICTURES

I think a fair market price, given California location, is $9,000 to $11,000.

While the engine may be great, it is old. A new engine is $12,000 to $14,000.

A new trailer in California will cost $3,000 to $4,500.
by Phil T
Tue Aug 22, 2023 5:01 pm
Forum: PERFORMANCE
Topic: 1982 OUTRAGE with HONDA BF150
Replies: 14
Views: 2679

Re: 1982 OUTRAGE with HONDA BF150

We are asking the questions to get you answers. We pick propeller that are good for MPG but also good for all speeds. If you select a prop that is only good between 18 to 22-nautical-miles=per-hour, the engine will have operational problems. Propeller selection is make and model dependent. One four-...
by Phil T
Tue Aug 22, 2023 11:13 am
Forum: PERFORMANCE
Topic: 1982 OUTRAGE with HONDA BF150
Replies: 14
Views: 2679

Re: 1982 OUTRAGE with HONDA BF150

The wide open throttle (WOT) rpm range for the BF150 is 5000-6000.

Q11: What is the engine speed at full throttle when the boat is lightly loaded?
by Phil T
Tue Aug 22, 2023 9:39 am
Forum: PERFORMANCE
Topic: 1993 Outrage 21 Re-power
Replies: 4
Views: 2016

Re: 1993 210 Outrage Re-power

There was no 210 Outrage in 1993. The 1993 Outrage 21 has a minimum power rating of 150-HP and a maximum power rating of 300-HP.

At the time it was introduced the method of attaining 300-HP was from twin 150-HP engines. Therefore, I doubt 100-lbs will make a measurable impact.
by Phil T
Sun Aug 20, 2023 8:00 pm
Forum: PERFORMANCE
Topic: 170 Montauk Engine Mounting Height Change
Replies: 9
Views: 2257

Re: 170 Montauk Engine Mounting Height Change

While the factory mounted the engine 1 hole up, dozens of Montauk 170 I owners have done testing and determined that 2-holes up, top bolt in the third hole counting down from the top is ideal for overall performance. Removing the bench seat and kicker will improve planing and overall performance as ...
by Phil T
Sun Aug 20, 2023 11:13 am
Forum: The GAM
Topic: Source for cube shaped nuts used on combined sidelight lamp bollards
Replies: 2
Views: 1875

Re: Source for cube shaped nuts used on combined sidelight lamp bollards

While I doubt they are sold separately, check with Derek or Jason at the parts desk of Nauset Marine. Email them at parts@nausetmarine.com .

http://www.nausetmarine.com
by Phil T
Sat Aug 19, 2023 9:16 pm
Forum: REPAIRS and MODIFICATIONS
Topic: 1969 SPORT 13: Leftover Part
Replies: 3
Views: 2002

Re: 1969 SPORT 13: Leftover Part

The part shown in Figure 1 is the backing plate for the bow railing support.

There are two of them, one on each side of the hull, forward to support the vertical stanchion. They insert from the outside into the two holes. The two machine screws threat into it.
by Phil T
Fri Aug 18, 2023 5:21 pm
Forum: PERFORMANCE
Topic: 1982 OUTRAGE with HONDA BF150
Replies: 14
Views: 2679

Re: 1982 Outrage & 150 HP Honda

If I had to guess the prop is possibly a Solas. We need to know the engine mounting height. How many empty holes are above the top bolts? What is the wide-open-throttle (WOT) rpm at top speed with a typical load? My list for the Outrage 18 with the Honda BF 150 includes**: Honda "Turbo" 14...
by Phil T
Fri Aug 18, 2023 1:37 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Life with my Carburetor Mercury-Yamaha FourStroke (continued)
Replies: 30
Views: 27062

Re: Life with my Carburetor Mercury-Yamaha FourStroke (continued)

One of the proven preventive measures when running a Mercaha motor is to add Mercury Quickleen to every gallon of gas. This seems to stop the carburetors from getting the perpetual gummed up condition
by Phil T
Fri Aug 18, 2023 1:32 pm
Forum: REPAIRS and MODIFICATIONS
Topic: Life with my Carburetor Mercury-Yamaha FourStroke (continued)
Replies: 30
Views: 27062

Re: Life with my Carburetor Mercury-Yamaha FourStroke (continued)

There is no grease nipple for the steering cable in the tilt tube only for the tilting feature of the engine. In the States the recommendation is to change the port side nut on the tilt tube with a nut that has a grease fitting. https://www.wholesalemarine.com/steersman-boat-steering-guard-1.html Fr...